Arduino: 1.8.15 (Windows 10), Board: "Arduino Nano, ATmega328P (Old Bootloader)"
Sketch uses 5262 bytes (17%) of program storage space. Maximum is 30720 bytes.
Global variables use 466 bytes (22%) of dynamic memory, leaving 1582 bytes for local variables. Maximum is 2048 bytes.
avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0xfc
avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x90
avrdude: arduino_read_sig_bytes(): (a) protocol error, expect=0x10, resp=0xfc
avrdude: error reading signature data for part "ATmega328P", rc=-3
avrdude: error reading signature data, rc=-3
avrdude: error reading signature data, rc=-3
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
Please Help. I want to update the code on it. Last time I uploaded a year ago
Try with board: "Arduino Nano, ATmega328P".
No Old Bootloader.
Related
I am new(new purched board and me also) in arduino programming. when I am uploading my code in ardino mega board (using Aurdino 1.8.2) i am getting following error
Arduino: 1.8.2 (Windows 10), Board: "Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)"
Sketch uses 1482 bytes (0%) of program storage space. Maximum is 253952 bytes.
Global variables use 9 bytes (0%) of dynamic memory, leaving 8183 bytes for local variables. Maximum is 8192 bytes.
C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega2560 -cwiring -PCOM3 -b115200 -D -Uflash:w:C:\Users\Admin\AppData\Local\Temp\arduino_build_393128/Blink.ino.hex:i
avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"
Using Port : COM3
Using Programmer : wiring
Overriding Baud Rate : 115200
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
An error occurred while uploading the sketch
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_getsync(): timeout communicating with programmer
avrdude done. Thank you.
How i solve this problem.
My setting are as follows
.
rest of them are as default. also my driver are up to date in device manager.
First, try a loopback test. If that fails, you have a problem with the hardware most likely. If it passes, try replacing the avr directory with another version. Additionally, if pins 1 or 0 are connected to anything, this error could be caused. That is because these pins are used for Tx/Rx. Additionally, the bootloader for the mega will break if you use !!! in your code. If all of that fails to help, try reinstalling the FTDI drivers.
I am trying to upload a sketch and getting below error:
Except the usual connection my GPIO 0 is grounded.
Arduino: 1.8.1 (Windows 10), Board: "Generic ESP8266 Module, 80 MHz, 40MHz,
DOUT, 115200, 512K (64K SPIFFS), ck, Serial1, All"
Sketch uses 232813 bytes (53%) of program storage space. Maximum is 434160 bytes
Global variables use 34092 bytes (41%) of dynamic memory, leaving 47828 bytes for local variables. Maximum is 81920 bytes.
error: failed reading byte
warning: espcomm_send_command: cant receive slip payload data
warning: espcomm_sync failed
error: espcomm_open failed
error: espcomm_upload_mem failed
You must have a bad connection. I recommend that you follow this scheme that I leave here.
ESP01 connection with Arduino UNO
You can also consult this complete guide on the ESP01 (https://programarfacil.com/podcast/como-configurar-esp01-wifi-esp8266/) that although it is in Spanish, is very simple to follow.
Make sure GPIO 0 is grounded, and then reset the ESP8266. Also make sure you have 3.3v coming in to CH_PD and RST. Set baud rate to 115200 unless you changed it already.
avrdude: Device signature = 0x1e9514
avrdude: Expected signature for ATmega328P is 1E 95 0F
Double check chip, or use -F to override this check.
If the bootloader has been compiled for ATmega328P it may not work as expected on 328PB (I personally experience issues on application code).
Also the 328PB is a quite recent chip and may not be completely supported by avrdude ref
When trying to upload the sketch from the command line I get a
avrdude -vvv -F -V -c arduino -p ATMEGA328P -P /dev/ttyACM0 -b 115200 -U flash:w:test.hex
avrdude: Version 6.0.1, compiled on Oct 21 2013 at 15:55:32
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2009 Joerg Wunsch
System wide configuration file is "/etc/avrdude.conf"
User configuration file is "/home/toni/.avrduderc"
User configuration file does not exist or is not a regular file, skipping
Using Port : /dev/ttyACM0
Using Programmer : arduino
Overriding Baud Rate : 115200
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00
but from the Arduino IDE it works flawlessly, so, obviously, the IDE is doing something I don't know about.
I've tried activating "Show detailed output during upload" but the output window history is way too short to view the commands launched. I can only see the end of the successful upload.
I'm guessing the IDE resets somehow the Arduino to talk to the booloader before the already loaded sketch starts running
Ho could I do this from the command line (without the IDE) ?
I am trying to upload the blink sketch on my arduino.. I hav the com port sorted out( COM 11) adn installed the drivers exactly as described in the arduino.cc website. But everytime i try to upload the sketch, i get this error:
Binary sketch size: 30,724 bytes (
Binary sketch size: 30,724 bytes (of a 32,256 byte maximum)
avrdude: stk500_getsync(): not in sync: resp=0x0o
I have already tried different os( win 8 64 bit/ win 7 32/64 bit), but it still doesn't work. I am a beginner and i really need some serious help with this.. Thanx :)
This happened to me when I used a freeduino. What kind of board do you have? There are different kinds of Arduinoboards. The error "not in sync: resp=0x0o" means he can't recognize the Board. These are the steps that helped me:
- reinstalled the the Duino's driver
- selected the correct board in Tools->Board
- also check whether the USB-cable is working.
For more details follow these links:
Freeduino v0.1 avrdude: stk500_getsync(): not in sync: resp=0x00
http://forum.arduino.cc/index.php?topic=201710.msg1486452#