I have a comestero rm5 evolution coin validator and i try to read the output serial values on a serial monitor like putty or realterm and i get nothing. The cable works for sure as it connects with the program given by comestero.
The serial protocol says that i have to send 00 command then wait for answer then send 1D and then when i drop a coin i will get a value on my serial monitor..the thing is i have tried many combinations and still nothing..i want to use it on an arduino project
Related
I am trying to read BLE telegrams sent to a usb plugged reciever to my PC.
I am using a serial port reader ( used putty at first then tryed some other software from the net). However, I get nothing, not data at all sent; not from my sender not even any telegram from may be other unknowm devices that may be there advertising.
I have run mode on command line to give me information and it shows that my com port has a baudrate of 1200.
I must say this value was not fix it goes from 1200 to 57600.
I know that my data is sent at a baudrate of 57600: so I'm thinking may be the problem is that the baudrates being different it can't get the data but then it should come to a time where I can see at least some insignificant data of incomplete telegram. I have also tried to change the baudrate on the serial com port reader but same result nothing at all.
My question is what might be the problem and how can I fix it ? in other words having a BLE reciever and tranciever how can I read the telegrams on COM ports
I think my problem would best be explained with an example. Here is some Arduino Code:
void setup() {
Serial.begin(9600);
}
void loop() {
Serial.println(millis());
delay(1);
}
...and here is the output:
Now, those numbers at the beginning aren't just your regular old first-bytes-of-serial-data-are-always-messed-up numbers. Those numbers are left over from the last time I opened the serial monitor. How do I know this? Because I counted how many seconds had gone by since I last opened the serial monitor, and it all matched up.
So here's the big questioroonie,
How do I make this stop? It's breaking my java program that's supposed to read data from the Arduino's current "run instance"(I don't know the correct term), and not the last one.
There is nothing wrong with your Arduino. Remember, the USB connection is not a real RS-232 serial interface, it's simulated through USB. And that USB connection is controlled by a chip with its own buffer.
Bad news is, nothing you can do if you're using the USB cable to carry your RS-232 signals, other than to send some "filler characters" to purge the buffer. Too many buffers everywhere :) Send some terminal emulation commands like "clear the screen" and "form feed" etc. to empty the pipeline of stuff in the buffer.
Which reminds me -- we should all quit using the crummy Arduino serial monitor and be vocal about it. Instead, use TeraTerm or Putty or any other good-quality terminal emulator of your choice.
Or connect with real RS232 and an adapter and cable. My development machine has three serial ports, but that's what I do. Often computers today don't even have one handy.
I'm trying to write a simple code that sends a string to an xbee and one that sends the string back, I was able to do this with XCTU via console, but I want my arduino to send the string.
I was able to use a simple code that read my output from the serial monitor and sends it to an xbee connected via usb adapter, the problem is that I now wrote the code so it sends a predefined string like in the screenshot, but when I write into the monitor it still sends whatever I wrote instead of the static string. I'm also unable to read what I type into the xbee console from XCTU.
I'd love any assistance in this, I've tried uploading and resetting everything to no avail.
Screenshot of problem with the current code of the arduino on the left
You said you were using an Arduino to try to communicate with your XBee Zigbee module.
One thing you have to check is the connection between the TX and RX signals on the Arduino side and on the XBee Zigbee side.
I've helped someone on another forum who used this Seed Studio XBee shield :
If you look at the schematics of this shield, the XBee 'DOut' signal (Tx) is wired to the XB_TX line which can be connected to any of the AJ2 pin with a jumper.
Now on the Arduino side :
On this extract of the Arduino schematics, we can see that the ATMEGA UART has it's RX signal connected to pin 2 of the CPU which is wired to the IOL (AJ2) pin 0.
So, that means that on this shield, the jumper have to be placed between XB_TX and pin 0 of AJ2 to connect the XBee transmission signal (output) to the ATMEGA reception signal (input) [and also XB_RX have to be connected pin 1 of AJ2].
As you didn't mention what kind of shield you were using, you have to double check this point which is a common issue when using serial communication.
In a general way, ALWAYS connect 1 output to N input (except open-drain or open-collector outputs which can be connected together to make a wired OR but which finally have to be connected to N inputs)
Hope this helps
Best regards
From what I can tell on the documentation Xbee "hijacks" the serial system. Instead try blinking an LED to confirm data is being received and sent.
documentation
I am using an HM-10 module and Arduino UNO.
My requirement is to read data from ibeacons near me using Arduino. Is it possible? I have not been able to find any articles on this. All articles talk about connecting your android phone with arduino. Any idea?
Yes, it is possible. I'm using an HM-10 as an iBeacon detector (linksprite.com BLE 4.0 shield), and it is successfully detecting a RadBeacon running in iBeacon mode. Firmware on my HM-10 is version 540.
Before it would detect the RadBeacon, I had to send the HM-10 the following commands:
AT+ROLE1
AT+IMME1
AT+RESET
Then I used the AT-DISI? command, and the serial monitor is showing the broadcast received from the RadBeacon (and one other beacon) as follows (for example):
OK+DISISOK+DISC:4C000215:2G234454CF6D5A0FADF2F4911BA9FFA7:00000001AC:0CF3EE041CCE:-052OK+DISC:00000000:00000000000000000000000000000000:0000000000:B9782E08068C:-071OK+DISCE
In this example, the HM-10 is detecting my RadBeacon which has UUID of 2G234454...with signal strength of -052. It is also detecting another BLE beacon (my AppleTV downstairs) with UUID of B9782E08068C with signal strength of -071.
I'm definitely not very knowledgable about any of this stuff, but it seems to be working for me so far. Next challenge for me will be to figure out how to parse the text data being received. I'm mostly interested in the distance/signal strength data in order to trigger an action when the RadBeacon gets very close to the HM-10.
[Full disclosure: I jumbled some of the UUID numbers above since I'm not sure if any of this information is private or hackable or whatever]
[By the way, the nRF8001 BLE Shield will not do this since it only runs in peripheral mode.]
Yes, you can get the Min and Max number of the nearby iBeacons.
You need to Attach hm-10 to Arduino Uno.
Try using this Library : https://github.com/dinosd/BLE_PROXIMITY
You can configure suitable AT commands if you want to configure it. But it should work with default settings as well.
Use SoftwareSerial to access HM-10.
In firmware version V539 of the HM-10, it adds an AT command to list nearby iBeacons. The command is AT+DISI?. You would simply need to set up the Arduion to send that command over a serial port and parse the data it returns.
I'm new to serial communication. For a project I have to develop software for a vending machine. The vending machine basically consists of a host computer (a windows xp machine) and various peripherals. One of those peripherals is a coin acceptor. According to the documentation of the vending machine, the host computer communicates with the coin acceptor using the serial port. The only documentation I have is this document called "Multi-Drop Bus / Internal Communication Protocol" (the version I have can be found here: http://www.coin-acceptor.com.cn/Upload/EditorFiles/technicalfile/Mdb_version_4-2.pdf).
According to the docs it seems I have to create a serial port connection using a baud rate of 9600, 1 start bit, 1 stop bit, 1 mode bit and 8 data bits (page 29 in the linked document). The vending machine docs state that the coin acceptor is on COM port 6. I tried to create a connection like this using HyperTerminal and Putty. My first question is:
How do I properly create a connection to a device that supports this MDB 'protocol'? Putty and HyperTerminal don't allow me to set a "mode bit". I didn't find anything about the flow control and parity bit in the document. Can this be done using Putty or HyperTerminal? Or do I need some other tool to communicate over MDB?
My second question is about how to send a command to the device. I looked through the commands and saw a RESET command. According to the document, upon receiving the RESET command the device should reset itself and respond with an ACK. According to pages 33 and 63 of the document, if I want to send the RESET command to the coin acceptor, I can send the HEX value 08H over the serial line. Page 33 states that the coin changer listens to commands sent to addresses 08H until 10H (if I'm interpreting the document correctly, that is). Page 63 states that the RESET command is 08H with no data bytes. So can I just type "08H" into Putty and hit "enter" to send this command to the device? Or how can I send this command to the device over the serial line? Is this even the right approach or am I looking in the completely wrong place? The vending machine docs only contain this document for the coin acceptor. Thank you for the help!
Kind regards
Chris