I've edited eth0 and I made a mistake where my VPS is now offline and can not even connect to ssh with this message to the Recovery Console:
"Network is unreachable".
What is the command to configure / edit the network!?
Photo
If you have access to your machine. For example via tty then you can edit the network interface. After that you should restart the machine.
See this link to edit the network config.
https://www.serverlab.ca/tutorials/linux/administration-linux/configure-centos-6-network-settings/
If you dont have any access to you machine then you have to reset the machine. Some vps hosters have a recovery mode you can try this too.
Related
I have a VMWare Player (14.1.2 build-8497320) running a Ubuntu 18.04 guest on a Windows 10 host. The Ubuntu guest has a LAMP stack that runs a few web applications. I am using NAT to connect the Ubuntu guest to the Windows host's network.
I can access these applications by using the local IP address of the guest (e.g., http://192.168.80.128/mediawiki) from my Windows host. But I want to access it like so from my Windows host: http://localhost/mediawiki. I think this should be possible if I can forward the port 80 of my Ubuntu guest to that of the Windows host.
How do I make this happen please? I don't have access to VMWare Workstation and its Virtual Network Editor.
Edit: I should probably add the motivation for wanting to do this. Basically, I want to avoid figuring out the IP address of the virtual machine everytime I access the web applications.
The (further) reason is that the local IP address of the Ubuntu guest might (I suspect) change, and that will affect quite a few things, such as the base URLs configured in the webapps' configuration files (e.g., the $wgServer variable in LocalSettings.php of MediaWiki).
VMWare Player supports port forwarding over NAT natively:
In the file C:\ProgramData\VMware\vmnetnat.conf put under section [incomingtcp] a line like:
80 = 192.168.80.128:80
Then restart the VMWare NAT Service :
net stop "VMWare NAT Service"
net start "VMWare NAT Service"
Source/credits: https://hitchhikingtheweb.wordpress.com/2014/09/02/portforwarding-with-vmware-player-and-nat/
Also: VMWare documentation of this
You can do it using SSH Tunneling for example.
From windows you open a tunnel from the windows port 80 to the ubuntu port 80.
You can do it using Putty on Windows and having the ssh deamon running on ubuntu, which I guess you should already have.
There are many tutorials on how to do this.
I'll add just one link, but you can always google it and find one that suites you.
Portforwarding with SSH (Putty)
For the possible changes in the guest’s ip:
If you can’t fix the ip in settings then perhaps you can edit the windows hosts file and add a host name for the current Ubuntu ip. Then build the urls using the host name. If the ip changes you change it in the hosts file.
I've tried every adapter settings to be able connect internet through VM, but VM seems it can't connect in bridged mode and also NAT mode.
I tried to run couple of commands such as
service networking down
service networking start
ifconfig eth0 down
ifconfig eth0 up
None of them seems working.
Please tell me what I should do
Thanks
You might delete or disable one of VMware services. You can open services.msc via Run to search vmware services.
Please go Edit > Virtual Network Editor on your VMware
You need to get administrator previleges to Restore Defaults first
click on Change Settings button.
Click on Restore Defaults and wait for it finish
I am using apache cloudstack. System VMs are in running state but unable to download system template. when I am login to system VMs through ssh using linked local ip then the it is not able to ping DNS,Management server and host.
check it has the correct management server ip and all routes are proper.
You could try a destroy to recreate the SSVM.
Host: Windows 7 running lastest VBox + Extension pack
Vm1: lubuntu 3.10
Vm2: Ubuntu server 12.04.3
Problem: Can't get VMs talk/ping each other AND ping the internet at the same time
NAT: VMs have same IP, using ping/ssh is like checking connectivity/connecting to self, lol; can ping internet, can't ping each other
Bridged: VMs get unique IP; can ping each other, not the internet
Host-only: VMs get unique IP; can ping each other; not the internet
Internal network:
intnet, needs to be defined/added to windows 7, however, window 7 not accepting VBOXMANAGE add command, giving errors. VMs wait for network configuration, another 60 seconds and start without a network.
What else can I do?
Change VM to use NAT Network, generic driver... ???
edit /etc/network/interfaces?
change route?
use squid?
Following Lubuntu Networking Message pops up in Lunbutu GUI:
network service discovery disabled
your cuurent network has a .local domain which is not recommended and incompatible with the avahi network service discovery the service has been disabled.
Can anyone help?
Refresh your MAC address using Virtual Box machine settings and remove the kernel’s networking interface rules file so that it can be regenerated:
sudo rm -f /etc/udev/rules.d/70-persistent-net.rules
sudo reboot
It will work for your clone VM.
I am using VMWare Player 3.1.0 on Host OS Windows 7 Professional 64-bit. My guest is is SUSE Linux ES 10. My guest OS (SUSE) runs JBoss App Server which I access from host using HTTP. I used a "Bridged" connection to set up all this.
My problem:
When I am connected to network on the Host (using wired network adapter) I can connect to the http server on the Guest OS and browse the application. However, when I am disconnected from the network on Host (unplugged the wire), I cannot access to the guest OS app server and browse the application. I use the guest OS ifconfig command to find out ip address of the guest OS. This ip address does not change whether connected or disconnected. I have even tried using Wireless Data card, but that does not work either.
I have tried "NAT" as well as "Host Only" connection and rebooted the guest but it does not work either. I think for some reason the guest OS can only recognize the physical network card (which is disconnected).
I need to run this machine (my laptop) independently of the network because I use this for demo and need to be able to connect from my host OS to Guest OS.
I am not sure I understand exactly what you are trying to do, but I do know setting up a working NAT configuration will offer you the most flexibility.
Click the networking icon and select settings, Select NAT.
Follow these steps on your Unix OS
cd /etc/sysconfig/network-scripts
Make a backup of your ethernet adapter configuration
cp ifcfg-eth0 ifcfg-eth0.bak
Next modify the settings to look like the following:
DEVICE="eth0"
BOOTPROTO="dhcp"
HWADDR="What ever was here on your system"br/>
NM_CONTROLLED="yes"
ONBOOT="yes"
Save your changes
Restart your network adapters
/etc/init.d/network restart
Try nslookup www.google.com
You should now be able to connect back and forth from your Windows Host and Linux guest.
theJay28
-p.s. I had screenshots, but I do not have the 10 points yet to post images.
I figured that the solution is to restart the VM after making the changes to the NetWork setting on the VMWare. I selected Network for the VM as "Host Only" shutdown the VM and started it again. After that I was able to do what I wanted to do (i.e. browse the web application on guest from the browser in the host machine) without connecting the host to the network.
So key to the solution in my case was to make the network changes and restart the VM.
Any comments suggestions welcome...