I have an Arduino controlling a lamp through a relay module, everything works fine for some hours, but now it stops working. The led to on/off as expected, but i cant hear the "click" anymore, and now it is always on.
A relay module can burn out? My lamp is 250w/110V
Problem SOLVED: The issue was that i had others sensors connected to Arduino 5V output pin (the relays was already on a separated 5V), and that was getting current from arduino board causing arduino not able to turn on the relay coil.
After change sensor to use a separated 5V source (with more current) everything works fine again.
My advise: be careful to use arduino 5V or 3.3V as a source power because it has low current, causing errors or even restarting arduino.
Related
I've just recieved my very first esp32cam (AI THINKER) today and I was excited to test it, but I'm unable to upload any code to it. I'm always getting the following error:
Failed to connect to ESP32: Timed out waiting for packet header
So, the FTDI I'm using is the FT232r with the following wiring scheme
FTDI Wiring
How I reproduce this error:
Plug everything
Order IDE to upload the sketch
Wait for the "connecting" text
Press the RST button
Also:
Plug everything
Press the RST button
Order IDE to upload the sketch
I've already tried:
Switching to 3.3v (plugged on 3.3v pin)
Using external 5v power supply (plugged on 5v pin)
Using another computer
Swapping RX TX
Trying in different upload speeds
Holding RST button
Switching board between ESP32 Wrover Module and AI Thinker ESP32
I'm I doing something wrong or there's just something faulty?
I have delved for a solution in this regard for weeks and it seems I have a solution.
Findings-
FTDI module is probably faulty or not supported for each instance.
Aithinker Board is not compatible with esspressif (use ESP32Wrover, more details below )
I have an esp32cam from Esspressif, not Aithinker.
I was trying with FT232rl , No matter what Voltage/jumpers/USB cable I used, it didn't work. Always stuck with fatal timed out error.
After many futile attempts with FTDI breakout, I gave my Arduino UNO a try (please note my UNO has mega16u2 chip as USB serial chip (top right corner just beside the oscillator) and fortunately it worked.
I have read that CP2102 is also working.
**Here are the steps to follow-**
Arduino ESP32Cam connections
3.3 Arduino --------- 3v Esp32CAM
GND Arduino ------------ GND Esp32CAM
RESET Arduino to Ardunio GND
RX Arduino -------------- VOR Esp32CAM (this is not a mistake RX to rx & TX to tx)
TX Arduino -------------- VOT Esp32CAM
GPIO 0(zero)(written as IO0) Esp32CAM to GND Esp32CAM
I didn't have any need to press the reset button in any part of the operation before & during uploading.
I am assuming You have pre-installed the esp32 board manager.
Now select the correct COM port where your Uno (in this case) is
plugged in.
Select the correct board as mentioned
Tools>Board>ESP32 Arduino > select ESP32 Wrover Module
Some uploading setups are to be Done (Under Tools, these will only appear when the Wrover module is selected )
Upload speed -- 115200
Flash Frequency -- 40Mhz
Flash Mode -- QIO
Partition Scheme --- Huge App
Port ---- select the right com port for your breakout or UNO
JUST press upload and relax
After a while, you will be able to see this message
Leaving...
Hard resetting via RTS pin...
Disconnect the Esp32Cam GPIO 0 and GND
Power the ESP32Cam with 5/3v with external power supply (Arduino or other breakouts may not be able unless you are connected with a Powered USB Hub)
keep TX, RX, & GND of the 2 boards connected, don't disconnect Arduino Reset and GND.
Press Reset on ESPCAM and open Serial monitor and you will be able to see the IP address of the cam if it was configured with your wifi correctly.OR get any network scanner App on android or windows.
I hope it helped.
Pre-requisites for flashing:
ArduinoIDE 1.8.12
Core ESP32 1.04 (at time of writing)
Select board AI Thinker Cam
uplooad speed 921600
freq 240Mhz
flashfreq 80Mhz
mode QIO if not working try DIO
partition scheme default
Serial monitor is closed
NO hardware connected to the pins of the ESPcam
Make sure the USB cable is a data cable and NO loading cable only
check Windows device manager if programmer is shown and has max speed / 8n1 hardware
Connections
FTDI - ESP32
GND GND
5V 5V
TXD UOR
RXD UOT
If you use an AIThinker Cam clone you have to ground GIPO 0:
connect GPIO 0 with a dupont wire connected to GND
press reset
compile and upload (use AI THINKER CAM)
optional:
press reset
upload filesystem data (SPIFFS)
disconnect GPIO 0 and GND
press reset
code should execute
And yes you have to do it every upload, on my dev board I soldered a little switch with proper isolationSome more solutions from experience:
If there is still a problem use a 10K (or so) pull-down resistor between RX0 and GND (test on breadboard before soldering)
Pressing and holding (!) the boot-button while uploading on some "bad" boards
Happened with a "normal" ESP32 board to me - just to be sure - I got an ESP8266 in an ESP32 packaging. Configuring for the ESP8266 solved the issue of uploading.
In my case I forgot to remove the SD card. Other users recommended removing unnecessary connections to the pins-- and the SD card technically uses some of those :)
This was solved by using other jumpers. It seems one of the jumpers used in the wiring was faulty.
If you're having the same issue and tried everything in this post, try checking your cables!
Another solution here. Just to add, I tried everything on this QA, as well as many other things suggested online. e.g. tested by powering from 3.3V then 5V, various permutations of holding the reset button down and disconnecting IO00 from GND at the point of flashing. Changing various settings in Arduino IDE/
I was unable to flash a single one of the 5 ESP32-CAM boards I bought. Spent a good two hours on it. I even continuity tested every pin on the board to its ESP32 chip pad, and all the hookup wires were tested too. The board seemed fine.
Then I soldered a 100uF capacitor between 5V and GND, and used my USB-UART 5V power... tested and worked straight away. No need to pull out the IO00->GND connection and no need to press RST button on the board during flashing. (Of course, pull out IO00->GND after flashing complete.
So - it was a power problem.
I can only guess that the cheapo regulator they used on the copy of board that I got was not quite efficient enough, but basically that capacitor resolved the issue.
p.s. the ESP on board was marked "ESP32-S". I selected "AI Thinker ESP32-CAM" in Arduino IDE as suggested by most people online, and this worked.
There are 3 pins marked GND on the ESP32-CAM board. Buuuuut (!) the one marked GND/R just by the U0T is NOT connected to other grounds or anywhere else I could had find. Check with a multimeter and use a REAL GND. It just worked for me after days of puzzling.
If you try it with arduino it works but its needed to press reset button on esp32 before you upload your code
Basically I was facing the exact same problem fro quite some time. What worked for me was that as the chip was flashing, shifting the power wire from 5V to 3V3 pin. I do not know why but it workes. When esptool starts flashing at 2%, switching the cable just then, despite having 5V from supply into the 3V3 point made the flashing successful. I do realize this is probably a bad answer to your problem since it involves oversupplying voltage to the chip on the wrong point as it is flashing and could damage the chip. However, if anyone is tired of debugging and are at the point where you are considering throwing the chip away, might as well try my method. For other's who value their chip, don't try this method and if you still do, kniw it is at your own risk. But it worked for me after 3 days of just messing around with connections.
I've just recieved my very first esp32cam (AI THINKER) today and I was excited to test it, but I'm unable to upload any code to it. I'm always getting the following error:
Failed to connect to ESP32: Timed out waiting for packet header
So, the FTDI I'm using is the FT232r with the following wiring scheme
FTDI Wiring
How I reproduce this error:
Plug everything
Order IDE to upload the sketch
Wait for the "connecting" text
Press the RST button
Also:
Plug everything
Press the RST button
Order IDE to upload the sketch
I've already tried:
Switching to 3.3v (plugged on 3.3v pin)
Using external 5v power supply (plugged on 5v pin)
Using another computer
Swapping RX TX
Trying in different upload speeds
Holding RST button
Switching board between ESP32 Wrover Module and AI Thinker ESP32
I'm I doing something wrong or there's just something faulty?
I have delved for a solution in this regard for weeks and it seems I have a solution.
Findings-
FTDI module is probably faulty or not supported for each instance.
Aithinker Board is not compatible with esspressif (use ESP32Wrover, more details below )
I have an esp32cam from Esspressif, not Aithinker.
I was trying with FT232rl , No matter what Voltage/jumpers/USB cable I used, it didn't work. Always stuck with fatal timed out error.
After many futile attempts with FTDI breakout, I gave my Arduino UNO a try (please note my UNO has mega16u2 chip as USB serial chip (top right corner just beside the oscillator) and fortunately it worked.
I have read that CP2102 is also working.
**Here are the steps to follow-**
Arduino ESP32Cam connections
3.3 Arduino --------- 3v Esp32CAM
GND Arduino ------------ GND Esp32CAM
RESET Arduino to Ardunio GND
RX Arduino -------------- VOR Esp32CAM (this is not a mistake RX to rx & TX to tx)
TX Arduino -------------- VOT Esp32CAM
GPIO 0(zero)(written as IO0) Esp32CAM to GND Esp32CAM
I didn't have any need to press the reset button in any part of the operation before & during uploading.
I am assuming You have pre-installed the esp32 board manager.
Now select the correct COM port where your Uno (in this case) is
plugged in.
Select the correct board as mentioned
Tools>Board>ESP32 Arduino > select ESP32 Wrover Module
Some uploading setups are to be Done (Under Tools, these will only appear when the Wrover module is selected )
Upload speed -- 115200
Flash Frequency -- 40Mhz
Flash Mode -- QIO
Partition Scheme --- Huge App
Port ---- select the right com port for your breakout or UNO
JUST press upload and relax
After a while, you will be able to see this message
Leaving...
Hard resetting via RTS pin...
Disconnect the Esp32Cam GPIO 0 and GND
Power the ESP32Cam with 5/3v with external power supply (Arduino or other breakouts may not be able unless you are connected with a Powered USB Hub)
keep TX, RX, & GND of the 2 boards connected, don't disconnect Arduino Reset and GND.
Press Reset on ESPCAM and open Serial monitor and you will be able to see the IP address of the cam if it was configured with your wifi correctly.OR get any network scanner App on android or windows.
I hope it helped.
Pre-requisites for flashing:
ArduinoIDE 1.8.12
Core ESP32 1.04 (at time of writing)
Select board AI Thinker Cam
uplooad speed 921600
freq 240Mhz
flashfreq 80Mhz
mode QIO if not working try DIO
partition scheme default
Serial monitor is closed
NO hardware connected to the pins of the ESPcam
Make sure the USB cable is a data cable and NO loading cable only
check Windows device manager if programmer is shown and has max speed / 8n1 hardware
Connections
FTDI - ESP32
GND GND
5V 5V
TXD UOR
RXD UOT
If you use an AIThinker Cam clone you have to ground GIPO 0:
connect GPIO 0 with a dupont wire connected to GND
press reset
compile and upload (use AI THINKER CAM)
optional:
press reset
upload filesystem data (SPIFFS)
disconnect GPIO 0 and GND
press reset
code should execute
And yes you have to do it every upload, on my dev board I soldered a little switch with proper isolationSome more solutions from experience:
If there is still a problem use a 10K (or so) pull-down resistor between RX0 and GND (test on breadboard before soldering)
Pressing and holding (!) the boot-button while uploading on some "bad" boards
Happened with a "normal" ESP32 board to me - just to be sure - I got an ESP8266 in an ESP32 packaging. Configuring for the ESP8266 solved the issue of uploading.
In my case I forgot to remove the SD card. Other users recommended removing unnecessary connections to the pins-- and the SD card technically uses some of those :)
This was solved by using other jumpers. It seems one of the jumpers used in the wiring was faulty.
If you're having the same issue and tried everything in this post, try checking your cables!
Another solution here. Just to add, I tried everything on this QA, as well as many other things suggested online. e.g. tested by powering from 3.3V then 5V, various permutations of holding the reset button down and disconnecting IO00 from GND at the point of flashing. Changing various settings in Arduino IDE/
I was unable to flash a single one of the 5 ESP32-CAM boards I bought. Spent a good two hours on it. I even continuity tested every pin on the board to its ESP32 chip pad, and all the hookup wires were tested too. The board seemed fine.
Then I soldered a 100uF capacitor between 5V and GND, and used my USB-UART 5V power... tested and worked straight away. No need to pull out the IO00->GND connection and no need to press RST button on the board during flashing. (Of course, pull out IO00->GND after flashing complete.
So - it was a power problem.
I can only guess that the cheapo regulator they used on the copy of board that I got was not quite efficient enough, but basically that capacitor resolved the issue.
p.s. the ESP on board was marked "ESP32-S". I selected "AI Thinker ESP32-CAM" in Arduino IDE as suggested by most people online, and this worked.
There are 3 pins marked GND on the ESP32-CAM board. Buuuuut (!) the one marked GND/R just by the U0T is NOT connected to other grounds or anywhere else I could had find. Check with a multimeter and use a REAL GND. It just worked for me after days of puzzling.
If you try it with arduino it works but its needed to press reset button on esp32 before you upload your code
Basically I was facing the exact same problem fro quite some time. What worked for me was that as the chip was flashing, shifting the power wire from 5V to 3V3 pin. I do not know why but it workes. When esptool starts flashing at 2%, switching the cable just then, despite having 5V from supply into the 3V3 point made the flashing successful. I do realize this is probably a bad answer to your problem since it involves oversupplying voltage to the chip on the wrong point as it is flashing and could damage the chip. However, if anyone is tired of debugging and are at the point where you are considering throwing the chip away, might as well try my method. For other's who value their chip, don't try this method and if you still do, kniw it is at your own risk. But it worked for me after 3 days of just messing around with connections.
I bought esp8266 with serial wifi wifi card
I connect RX to TX; TX to RX; VCC to VCC; GRD to GRD;
I cant communicate with the board not if program mode and not in UART mode; the reset do nothing.
the red led on the board is on.
I connected the wifi serial to Arduino uno board.
try to upload sketch i got the following error:
warning: espcomm_sync failed
error: espcomm_open failed
error: espcomm_upload_mem failed
Any help or guides will help me to solve the issue.
Since I have had numorous of problems with my ESP8266 modules, this is what I generally watch for:
Output is 3.3v
Swap over tx and rx. Some boards have them swapped for some reason (searched for days for this!!)
When uploading the code, first the code compiles, then the code uploads. During the compile process, keep the reset button (or pin) pressed. As soon as you see the "uploading" status message, you can release it.
Make sure the GPIO0 is connected to the ground and (depending on which version you have) the GPIO15 as well.
When grounding the GPIO0 and GPIO15, use a resistor for each (between 2K and 10K will do).
I've spent two nights trying to upload firmware so I'll just repeat what helped me since there's not so many solutions:
First in Serial Monitor make sure that your chip responses to AT commands. There's no point in going further without achieving it. If you fail here then it's time to check your commutation, power source, etc.
While uploading: 1. Ground GPIO-0 pin. 2. In Arduino IDE press Upload button. 3. Code starts compiling. 4. As soon as you see that code starts uploading ground RST pin for just a blink. Before I reseted the chip too early so I had sync failed problem as you did. It took me a while to "catch" this moment for resetting the chip. Still I upload new firmware in 4-5 takes.
Before flashing firmware, please hold FLASH button, and press RST button once. When our firmware download tool released, it will flash firmware automatically and needn't press any button
I have this really weird issue where grounding GPIO 0 didn't work for me, but after a lot of trial and error I managed to upload the sketch connecting directly both gpios to ground in the arduino board and it worked. Really strange.
I had the same issue. In my case, I was uploading while in another terminal program I was checking for serial data. After I closed the serial monitor (and let Arduino IDE use the serial port) the problem was resolved partially.
The other half of the problem involves carefully pressing the button GPIO0 and then RESET.
This helped me achieving that.
I had the same issue, but after I set the Programmer to "AVR ISP" in the Arduino IDE/Tools, after that the upload was successful and it worked fine.
Hope it helps.
First you have to make sure that the Arduino IDE has the ESP8266 libraries installed. To do that, go to file>preferences and under Additional Boards Manager URLS, paste this link:
http://arduino.esp8266.com/stable/package_esp8266com_index.json
Then, go to tools>board>boards manager. Scroll until you find the link for ESP, than download it.
Once you select all the info for the board change the programmer to "AVR ISP"
Finally, to download the code, hold down the GPIO0 button and press the reset button once. Finally, hit download!
To use serial monitor, you may need to use the 115200 speed as it is not the default.
Hope this helps!
Please downlode and install these driver as per OS i spent 6 hours today and finally this was the solution.
https://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx
Look follow the leads and you will get the proper output as 'OK' in reply to AT command, just search for Arduino15 file in C directory of your computer, it will be in somewhere at C/users/app data and delete it, then set the Arduino to arduino uno board or whatever board you are using and connect the Esp8266 as, UNO --- ESP8266
RX ----- RX
TX ----- TX
GND --- GND
3.3V --- VCC and CH_PD
Once Connected open the Serial Monitor and set "Both NL & CR" and Baud to 9600.
Send "AT" to test. If nothing comes up try different baud rates such as 115200 or 57600 and retest.
If you get "OK" reply then all is working.
I just bought the Wemos D1 and had the same problem: I could not upload my sketches. There were several reasons for this:
1) I did not have the CH340G drivers loaded on my Mac. Both Win and Mac platforms need these drivers. Linux does not. I found my drivers at http://sparks.gogo.co.nz/ch340.html
2) You need to add the board to your Arduino IDE. You can find the steps to do that at http://www.beerandchips.net/2016/01/24/wemos-d1-hands-on-with-the-new-arduino-compatible-esp8266-dev-board/
Once I completed those 2 steps (be sure to select the serial port) everything worked great and I can upload my sketches with no difficulty.
I had (too many/wrong) COM port(s). Find the right one and I't fine.
This worked for me this time in the following way to successfully upload sketch from IDE to esp8266 via arduino:
1) IDE Tools menu: upload speed 115200
2) opt this one in tools menu: Programmer- AVR ISP
3) Keep serial monitor closed. If com port not visible under Tools, disconnect and reconnect USB from laptop
4)Reset Arduino
5)Connect GPIO0 of 8266 to VCC(3.3V) for a blink and remove
6) Connect reset of 8266 to gnd for a blink and remove
7)GPIO0 grounded..keep this one gnded for the upload period
Hope this one works..
I'm in a situation and need some advice.
Scenario 1:
Arduino Uno/Genuino +
ICOMSAT SIM900 Module(http://www.itead.cc/icomsat.html)
(placed the jumpers such that Digital Pin 2 is rx and 3 is TX on the shield)
Code Used: The send receive SMS example code in the arduino website.(
(https://www.arduino.cc/en/Tutorial/GSMExamplesReceiveSMS)
Everything Works fine without a glitch.
Scenario 2:
Arduino Uno/genuino +
GSM breakout board(https://www.google.co.in/search?q=sim900A&espv=2&biw=1600&bih=717&source=lnms&tbm=isch&sa=X&ved=0CAYQ_AUoAWoVChMIqd748qb8yAIVYXumCh2s2Aaq#tbm=isch&q=sim900a+gsm+module&imgdii=9zJcFQBaoLAKzM%3A%3B9zJcFQBaoLAKzM%3A%3B7eDw6qGc3qZjMM%3A&imgrc=9zJcFQBaoLAKzM%3A)
Had loads of issues with softwareSeial.h library and ended up cross connecting the default on board rx/tx with GSM board's RX/TX and everything worked fine. (though I didn't liked the fact that everytime during programming I had to change connections to upload a sketch)
code used is from here (http://www.theengineeringprojects.com/2014/06/send-sms-with-arduino-uno-and-sim900d-using-at-commands.html)
Now my Problem:
Since the shields are very costly, I decided to settle on the cheaper boards for my project. But the Code used for the GSM shield was so easy to understand (since the library was doing all the heavy lifting) I tried to use that. I connected Rx of GSM board to pin 3 and TX to pin 2 of arduino and uploaded the same code I used for the GSM shield scenario. But the code won'r work, I tried to tinker a few blocking things like the enable pin code where the shield is brought up etc. but no luck. Can anyone put some light on it, has this been tried before, is it not supposed to work the was i want it to ?
Thanks a lot in advance.
I have done my project finally :) , but i noticed that the arduino board on startup it's some digital pins goes high for a bit time 1 seconds or little more! and this causes problem in my project because i'm using it in starting dc motor.
I forgot to mention that i have 2 relays connected with arduino and they are triggered on arduino startup or with resetting it, then my code works perfectly. I tried doing pull up resistor and pull down resistor but it seems same situation. Also tried (INPUT_PULLUP) and no result.
Any suggestion please?
I had the same problem when booting the arduino/connecting to a power source. Only using digitalWrite(pin, LOW) in void setup() did not work for me.
Every pin needs to be connected to a physical pull-down 10kOhm resistor in parallel to whatever you're controlling.