My new Arduino Uno Wifi, stops responding to wifi if left inactive. To be more specific, after 2-3 hours of no wifi usage:
I cannot access the build-in configuration page of the Arduino's wifi section
Loaded programs which use Wifi are not receiving any commands via my browser
loop() continues to run just fine
It somehow seems that the wifi section of my Uno Wifi "sleeps" after some arbitrary interval.
Using code to periodically reset the board (by sending HIGH to the reset pin of the board) did not solve the problem. As soon as the reset takes place, loop() starts executing just fine, but wifi connection is still impossible to obtain.
Things I usually do to gain access to my board AFTER wifi is lost:
Hard reset the board (unplug power and plug it again) -> almost always works
Try to access arduino from several different wifi devices hoping that the board somehow "wakes up" -> occasionally works but only after 4 or 5 minutes (sometimes hours) of failed attempts
My router seems to be fine. Another web server which I have set up in a wifi-connected laptop has had no hiccups (even after a long time of inactivity). Moreover I've never had any connection problems with my router so far.
This is giving me a hard time! Could anybody be of any help?
Is my Arduino Uno faulty?
Many thanks in advance
George
Here's my configuration:
Arduino Uno Wifi Developer edition (built-in wifi support)
Arduino IDE 1.8.0 (I'm using the Linux version installed on Ubuntu 12.04 )
I have already connected my arduino to my home network and gave it a static IP 192.168.2.50
WIFI mode: STA
Wifi channel: 1
SLIP status enabled
MQTT status disabled/disconnected
code:
int i=0;
void setup() {
pinMode(13,OUTPUT);
}
void loop() {
if (i==1){
digitalWrite(13, HIGH);
i=0;
}
else{
digitalWrite(13,LOW);
i=1;
}
delay(1000);
}
It seems that I have been a victim of an extreme ambiguity caused by the .org fork of arduino.
Arduino.cc and Arduino.org boards are NOT 100% compatible with each other.
To be more specific, the examples that come with the IDE (and are based on the the wifi shield of arduino.cc) DO NOT function with aruduino-uno-wifi (the one with the embedded wifi section)
Apart from that, it seems that arduino-uno-wifi has firmware that is way behind the arduino.cc (in terms of features as well as code quality). This has frustrated several users as you can see here:
Issue 2: Rename this fork and use less confusing versioning
Issue 10: Please stop doing this !
Issue 6: Remove old licenses from sample code comments and take credit for everything
If you are interested of an arduino.org view of things visit here:
The full story
All of the above is information which I wish I had when ordering my new ardnino-uno-wifi board.
Moreover it is relevant with the question I've asked, since it indicates that my problem is most probably a bug of the uno-wifi board, so I should file a bug report (and keep hoping) instead of trying to fix my code.
Related
I am looking to modify my Scooba 450 vacuum to make it remotely controlled.
So I searched and came across this and this.
After trying different ways, I ended up getting it to work in python, with a computer running at 57600 baud. So far, so good.
But for it to be remotely controlled, I wanted to use an ESP32, I tried a lot, but I can't communicate with the robot.
Normally, when it is charging, it returns information about its battery. So I put it on charge, and tried to read his data with the ESP32, but no information comes in.
I tried connecting it directly with a micro USB to micro USB cable, but without result.
I also of course checked that the cable is working, that data is currently being sent from the Scooba.
The program:
void setup() {
Serial.begin(57600);
}
void loop() {
while (Serial.available()){
Serial.print((char)Serial.read());
}
}
My goal would be to be able to control it from a site, but before that, I must succeed in communicating with the Scooba. I don't necessarily need to be connected to the computer to know if data is being received, because I can see if the LED on it is on.
Thanks
I'm working on a project based on the ESP32 platform. The aim is to count the number of MAC addresses in the area, and transmit this information over WiFi (using an http POST request).
The first task is achieved by sniffing WIFI packets and collecting the contained addresses, following this example: https://blog.podkalicki.com/esp32-wifi-sniffer/
I believe that the code which "sniffs" the packets sets the ESP to run in promiscuous mode, and therefore I cannot connect to any AP anymore.
I've tried several solutions, first starting with timer interrupts. However this approach always led to a Core Panic and reset of the chip.
I also learnt I could use RTOS to run different tasks in parallel on the two cores of the CPU, but that didn't help to solve the problem.
void wifi_sniffer_packet_handler(void* buff, wifi_promiscuous_pkt_type_t type)
{
if (type != WIFI_PKT_MGMT)//aggiungere filtro su RSSI a questa altezza.
return;
const wifi_promiscuous_pkt_t *ppkt = (wifi_promiscuous_pkt_t *)buff;
const wifi_ieee80211_packet_t *ipkt = (wifi_ieee80211_packet_t *)ppkt->payload;
const wifi_ieee80211_mac_hdr_t *hdr = &ipkt->hdr;
//some analysis and then print the MAC address
}
void setup() {
Serial.begin(115200);
timer = timerBegin(0, 80, true);
timerAttachInterrupt(timer, &chUpdate, true);
timerAlarmWrite(timer, 1000000, true);//timer, arr_val, reload=true
delay(4000);
wifi_sniffer_init();
timerAlarmEnable(timer);
}
// the loop function runs over and over again forever
void loop() {
//Serial.print("inside loop");
WiFi.begin(ssid, password);
while (WiFi.status() != WL_CONNECTED) {
delay(1000);
Serial.println("Establishing connection to WiFi..");
}
Serial.println("Connected to network");
}
I also noticed that the code in the loop gets stuck into the while, and is restarted every time the packet handler is run (I nevere get to see "Connected to network", but i see "Establishing connection to WiFi.." several times.
Anyone can explain me what's going on? Is there a different approach to achieve this result?
Thank you.
You may have two tasks and two cores, but the ESP32 still has only one wifi chip. The way your code is written (at least, the code you shared), you'll be trying to connect to a wifi network at the same time as you're trying to run promiscuous mode. You can do only one of those things at a time.
You'll need to stop promiscuous mode before you attempt to connect to an access point. Right now your code constantly attempt to connect to a wifi access point. Use a volatile variable to store the current mode - promiscuous or connected. Change it when you need to change states. Only attempt to connect to wifi when the variable says you want to be in connected mode.
There may be some code you need to run to turn off promiscuous mode when you change states, before you connect to a wifi access point.
If you're using wifi_sniffer_init() from the example you linked to, that code isn't meant to be run in an Arduino Core application. It does some network initialization that the Arduino Core will also do. It may not be safe to do that twice (it might work, it might not... but it's definitely not intended to be done that way).
You're setting an interrupt handle chUpdate() which you didn't share. I'd bet that's the cause of your Core Panics. You can do very little in an interrupt handler. You definitely can't call most Arduino Core functions or most ESP-IDF functions. Most code isn't protected against interrupts, so the timer interrupt can occur while data structures are in an inconsistent state. Re-entering code can corrupt the data structures and cause the kind of crash you described. You're best off setting a volatile variable and waking up a task that will do the work you need done while not in the interrupt handler.
Finally, you should call WiFi.mode(WIFI_STA); before you call WiFi.begin().
For anyone confused about why you can't connect to a wifi network while in promiscuous mode - what ESP8266 and ESP32 call "promiscuous mode" is really "wifi monitor mode", which lets you monitor a wifi radio channel and see all wifi frames sent on it. They use the term "promiscuous mode" differently from the rest of the industry. Usually "promiscuous mode" means seeing all the packets being sent on the network (wifi or hardwired) that you're connected to.
I know that it's been just over a year but THANKS to the info provided by romkey I think I solved this problem within my app by calling this routine before connecting to WiFi to upload MAC data.
void end_Scan_WiFi() {
esp_wifi_set_promiscuous(false);
esp_wifi_stop();
}
Followed by this ...
WiFi.mode(WIFI_STA);
WiFi.begin(ssid,pass);
I am using an Arduino Uno and GSM sim800l for a project. It looks like something is wrong and I don't know what it is. Here is my code:
#include <AltSoftSerial.h>
AltSoftSerial altSerial;
void setup() {
Serial.begin(19200);
Serial.println("AltSoftSerial Test Begin");
altSerial.begin(19200);
altSerial.println("Hello World");
}
void loop() {
char c;
altSerial.print("altSerial is working.");
if (Serial.available()) {
c = Serial.read();
altSerial.print(c);
}
if (altSerial.available()) {
c = altSerial.read();
Serial.print(c);
}
}
Its output was like this:
AltSoftSerial Test Begin (linebreak)
Hello World (linebreak)
ltSerial is ok⸮⸮M⸮ɥ⸮⸮⸮is okalt //insert long random garbage here
I tried changing the baud rate of the code and serial monitor to keep it matched, but it is not working. I tried to lower it as low as 300 and tried up to 19,200 baud as well.
I also tried menu Tools → Fix encoding and reload, but it still didn't solve the problem. It is my first time using this type of hardware, so please bear with me. My goal is to use it to send SMS messages. but right now I'm trying a smaller task with it to try and understand it better.
The Arduino IDE version I am using is 1.8.7.
It is a troubleshooting tree:
I am going to assume the system is Windows 10, but the basic ideas are the same if the way to achieve them are different.
Plug in your Arduino. You already said your serial monitor is set to 19200, but be sure you are sure, because that is very often the problem.
if you are sure of #1, open Control Panel → Device manager → Ports
If you don't see "Ports" in the list, then your computer isn't seeing the Arduino. This could be anything from a bad Arduino to a bad cable to a bad USB port on your PC. Try switching all those out one at a time to see if you can get anything talking to the COM port at speed. Since you were getting something in the serial monitor, this won't be your particular problem.
Click on "Ports" to expand it, and verify you see the Arduino listed. Right click on the Arduino, disable, and enable it again. See if that fixes the baud rate problem.
Look at Arduino properties
Does it say your device is working properly? If no, look at events and you will see an error description. Fix whatever it says is wrong. If yes, continue.
Port settings will likely be 9200, 8, None, 1, None. Even if your baud rate in the serial monitor window is 19200, you will still probably see 9200 in Device Manager, don't worry about it. It feels wrong, but it is normal. Microsoft seems to like keeping 9600 here, even if the last thing I did with this port was different. The data bits, and other settings listed above are a different matter.
next, click on Advanced
is your Arduino-assigned port number showing up? Does it say 'In Use' beside it? If it does, this is your problem. I know. Strange, huh? Trust me, if it says 'In Use', that means that something internal to Microsoft is using the port, but it isn't your Arduino. Power shell can help you resolve what has it, but that's another story, but the best bet now is reinstall your driver.
Click the Driver tab, and verify your Driver Provider is Arduino LLC. I've never seen it not that, but if it isn't, I would try to find out why.
Go ahead and Update the driver and reboot your computer, even if you aren't prompted to reboot, do it anyway.
Didn't fix it? In the Driver tab, Disable the device, and re-enable it. That might fix the problem, too.
Didn't it fix it? Don't uninstall the driver just yet.
Click Details. Do you see Arduino?
Look at the Events tab. If you see an error, then fix it.
Still not working? Uninstall your serial driver, and reinstall it.
Still no 19200? If you have garbage, the timing on your RX pin is not synchronized with the Arduino TX pin. You now need a logic analyzer, and that is more than can be covered here.
i got a brand new Teensy 3.2 with the blinking LED programm on it.
When I now tried to upload another programm on the teensy, Arduino says:
Teensy did not respond to a USB-based request to automatically reboot.
Please press the PROGRAM MODE BUTTON on your Teensy to upload your sketch.
The automatically starting window of Teensy, doesn't give me a chance to (for example) reboot the Teensy as well, so something of the connection seems to be wrong or something, but what...
Even if I mannualy press the pushbutton, it's still not possible to upload something. Any ideas why?
I have encountered this problem twice. The first I tossed out the board. This time, when I power it, it runs the last program I burned on it, but when I try to program it again, the LED stops blinking and everything stops.
The claim that it might not be a data cable is not reasonable, because how can it stop the current program unless it was told to. I doubt very much that +5V can provide such commands.
I have tried different cables, different USB ports, rebooting my Linux box, reinstalling (twice), checking the pins on the Teensy and the cable... no clue.
It always boots up in the old app (I left the blinker running to indicate "liveness"). I had programmed a message to come out the hardware serial port. Could that have been the problem? Wait... Is there a way to set the baud rate on the USB? I wonder if that is the problem! --
Banner(void) {
Serial.begin(9600);
Serial1.begin(115200);
};
The example had me programming the USB serial! I bet that is the problem! Better yet, does anyone know what the protocol is for talking to USB serial commander?
Under Ubuntu 18.04 install this https://www.pjrc.com/teensy/49-teensy.rules file into /etc/udev/rules.d
This is the main error that I get when I try to run my ARDUINO program. The full list of errors is as follows:
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_getsync(): timeout communicating with programmer
My code is as follows:
int led=13;
void setup()
{
pinMode(13,OUTPUT);
}
void loop()
{
digitalWrite(13,HIGH);
delay(1000);
digitalWrite(13,LOW);
delay(1000);
}
I have tried updating the drivers (they are fully updated) and downloading some programs. I have Windows 7 and my arduino is a MEGA 2560. It shows up in the Device Manager and all of my connections are correct. The green PWR light is on and so is the flashing L light. The RX and TX lights flash when I update. I have tried almost everything on the web. What is the problem?
Another possible reason for this error for the Mega 2560 is if your code has three exclamation marks in a row. Perhaps in a recently added string.
3 bang marks in a row causes the Mega 2560 bootloader to go into Monitor mode from which it can not finish programming.
"!!!" <--- breaks Mega 2560 bootloader.
To fix, unplug the Arduino USB to reset the COM port and then recompile with only two exclamation points or with spaces between or whatever. Then reconnect the Arduino and program as usual.
Yes, this bit me yesterday and today I tracked down the culprit. Here is a link with more information: http://forum.arduino.cc/index.php?topic=132595.0
The error message basically means that the programmer is unable to contact the bootloader on the device; the code you're trying to upload has no bearing on the problem.
What causes this can be numerous and varied, some possible issues:
UART communications
Blinking is happening, so hopefully you aren't using the wrong port. It might be worth checking again though, sometimes USB COM devices install on strange port numbers.
Connect TX to RX (and disconnect them from the AVR if possible) then open a terminal on the COM port, you should see characters echoed if you type them. If you don't, something is wrong up-stream of the chip, it could be the communications chip (I think the Arduino 2560 uses a secondary AVR instead of an FTDI for some reason, so that could be broken, either its software or hardware)
ATmega* bootloader
The AVR is not executing the bootloader for some reason. If the programmer is not resetting the micro before attempting to connect, this might be the reason. Try to reset the AVR (press and release the button) while the programmer is attempting to connect. Sometimes software that runs in a tight loop will prevent the bootloader from connecting.
Barring that, the fuses might have gotten messed up or the code erased. You would need to reflash the bootloader and proper fuses, again, see the appropriate info page for your device.
Arduino Mega 2560 only: ATmega8U/16U software
Might not be working and would need reprogramming. See the Programming section on the info page, you will need the firmware and Atmel-compatible DFU (device firmware update) software on your computer to reflash the target.
Hardware damage to the board, AVR(s), or FTDI chip
You're hosed; need a new chip.
Check this forum post for some more ideas.
I got this error because I didn't specify the correct programmer in the avrdude command line. You have to specify "-c arduino" if you are using an Arduino board.
This example command reads the status of the hfuse:
avrdude -c arduino -P /dev/ttyACM0 -p atmega328p -U hfuse:r:-:h
To my humble understanding, this error arises in different scenarios:
you have selected the wrong port or you haven't at all. go to tools > ports and select the com port with your Arduino connected to.
you have selected the wrong board. go to tools > board and look for the right board.
Do you have one of these Arduino replicas or you don't have the boot-loader installed on the microcontroller? I don't know the solution to this! if you know please edit my post and add the instructions.
(windows only) you don't have the right drivers installed. you need to update them manually.
sometimes when you have wires connected to the board this happens. you need to separate the board from any breadboard or wires you have installed and try uploading again. It seems pins 0 (RX) and 1 (TX), which can be used for serial communication, are problematic and better to be free while uploading the code.
Sometimes it happens randomly for no specific reason!
There are all kinds of solutions all over the internet, but sometimes hard to tell the difference between magic! Maybe the Arduino team should think of better compiler errors to help users differentiate between these different causes.
The same problem happened to me and none of the solutions above worked. What happened was that I was using an Arduino UNO and everything was fine, but when I bought an Arduino Mega 2560, no matter what sketch I tried to upload I got the error:
avrdude: stk500v2_ReceiveMessage(): timeout
And it was just on one of my windows computers and the other one was just ok out of the box.
Solution:
What solved my problem was to go to tools > boards > Boards Manager... and then on the top left of the opened windows select updatable in the Type section. Then select the items in the list and press update on the right.
I'm not sure if this will solve everyone's problem, but it at least solved mine.
Open Terminal and type:
$ sudo usermod -a -G dialout
(This command is optional)
$ **sudo chmod a+rw /dev/ttyACM0**
(This command must succeed)
This isn't really a fixing solution but it may help others. Unlike Nick had said for me it was due to code in my program. I have the mega ADK model. The issue was tied to a switch statement for processing and parsing the returned byte[] from the usb connection to the Android. Its very strange because it would compile perfectly every time but would fail as the OP had stated. I commented it out and it worked fine.
I was running this code from Arduino setup , got same error resolve after changing
serial port to COM13
GO TO Option
tool>> serial port>> COM132
If you use the ino command line:
ino upload
it can be because you use the arduino software at the same time, try to kill it.
I've connected to USB port directly in my laptop and timeout issue has been resolved.
Previously tried by port replicator, but it did not even recognized arduino, thus I chosen wrong port - resulting in timeout message.
So make sure that it is visible by your OS.
Ensure the serial monitor is not running and nothing is reading/writing dev/tty/S0 (or whichever port you're using), which may cause uploading interference.
I had the same problem, and in my case, the solution was updating the usb-serial driver using windows update on windows 10 device's manager. There was no need to download a especific driver, I just let windows update find a suitable driver.
I faced same problem. but Root cause of issue. Incorrect communication was set and thats why I occurred Communication timeout.
Solution: If you connected to laptop through USB port.
Change Port as USB. Please follow steps
Open Arduino-IDE
Go to Menu "Tools --> Port" and Select option "USB" { for me its showing as /dev/ttyUSB0 }
It working fine for me.
Something not yet mentioned is that this message also appears when the baudrate is not properly set... for Arduino, it is generally 115200.
My aurdino mega 2560 returned same error. It seems the problem exists in unofficial clones. The issue solved by pressing reset button just before uploading starts, as advertised in following video.
https://www.youtube.com/watch?v=tAzjO4v7oF4&list=LLDn5ewJDzz53IiwWmZTgQnQ&index=1