Arduino with two RC522 - arduino

Question

To pimp up my Carrera I'm going to build a round counter.
It contains an Arduino Nano, a lcd and 2 rc522 rfid-reader.
The readers share the pins for scd, miso, mosi and have own pins for sda and rst.
Actually I'm not able to get the two readers work together at the same time. Only if the one or the other reader is physically plugged (hardcore!) into the breadbord it works (without code changing). But not together.
It has to be an issue with my code, but where?
(The RFID-Communication ist inpired by the example from [addicore][1]http://www.addicore.com/v/vspfiles/downloadables/Product%20Downloadables/RFID_RC522/RFIDQuickStartGuide.pdf)
Is there anyone who has a hint for me?
#include <AddicoreRFID.h>
#include <SPI.h>
#include <LiquidCrystal.h>
#define uchar unsigned char
#define uint unsigned int
// create AddicoreRFID object to control the RFID module
/////////////////////////////////////////////////////////////////////
//set the pins
/////////////////////////////////////////////////////////////////////
//2 - SCK Digital 13
//3 - MOSI Digital 11
//4 - MISO Digital 12
const int SS1 = 8; //RFID1
const int RST1 = 9;
AddicoreRFID myRFID1 (SS1, RST1);
const int SS2 = 10; //RFID2
const int RST2 = A0;
AddicoreRFID myRFID2 (SS2, RST2);
//Maximum length of the array
#define MAX_LEN 16
//LCD init
// * LCD RS pin to digital pin 7
// * LCD Enable pin to digital pin 6
// * LCD D4 pin to digital pin 5
// * LCD D5 pin to digital pin 4
// * LCD D6 pin to digital pin 3
// * LCD D7 pin to digital pin 2
LiquidCrystal lcd1(7, 6, 5, 4, 3, 2);
//Counter
int a = 0;
int b = 0;
void setup() {
Serial.begin(9600);
//LCD init
init_lcd1();
myRFID1.AddicoreRFID_Init();
myRFID2.AddicoreRFID_Init();
}
void loop() {
uchar i, tmp, checksum1;
uchar status;
uchar str1[MAX_LEN];
uchar str2[MAX_LEN];
///////////// RFID1 ///////////////////
// 0x4400 = Mifare_UltraLight -Tag Type
str1[1] = 0x4400;
//Find tags, return tag type
// Manipuliert str1(!);
//AddicoreRFID::AddicoreRFID_Request(byte reqMode, byte *TagType)
status = myRFID1.AddicoreRFID_Request(PICC_REQIDL, str1);
if (status == MI_OK) {
serial_TagDetect(str1, 1);
}
//Anti-collision, return tag serial number 4 bytes
// Manipuliert str1(!);
status = myRFID1.AddicoreRFID_Anticoll(str1);
if (status == MI_OK) {
serial_TagData(str1);
lcd_counter(str1, lcd1);
//delay(500);
}
myRFID1.AddicoreRFID_Halt(); //Command tag into hibernation
///////////// RFID2 ///////////////////
str2[1] = 0x4400;
//Find tags, return tag type
status = myRFID2.AddicoreRFID_Request(PICC_REQIDL, str2);
if (status == MI_OK) {
serial_TagDetect(str2, 2);
}
//Anti-collision, return tag serial number 4 bytes
status = myRFID2.AddicoreRFID_Anticoll(str1);
if (status == MI_OK) {
serial_TagData(str2);
lcd_counter(str2, lcd1);
// liest sonst nonstop die Tags!
//delay(500);
}
myRFID2.AddicoreRFID_Halt(); //Command tag into hibernation
}
void init_lcd1() {
... inits the lcd ...
}
// Zählt das Auftreten der Tags
void lcd_counter (uchar *str, LiquidCrystal lcd ) {
... output to the lcd ....
}
// Meldet gefundenen Tag auf der Konsole
void serial_TagDetect(uchar *str, int reader) {
if (reader == 1) {
Serial.print("RFID1 tag detected: ");
} else {
Serial.print("RFID2 tag detected: ");
}
Serial.print(str[0], BIN);
Serial.print(" , ");
Serial.print(str[1], BIN); Serial.println(" ");
}
// gibt Tagdaten auf der Konsole aus
void serial_TagData(uchar *str) {
uchar checksum1 = str[0] ^ str[1] ^ str[2] ^ str[3];
Serial.print("The tag's number is: ");
//Serial.print(2);
Serial.print(str[0]);
Serial.print(" , ");
Serial.print(str[1], BIN);
Serial.print(" , ");
Serial.print(str[2], BIN);
Serial.print(" , ");
Serial.print(str[3], BIN);
Serial.print(" , ");
Serial.print(str[4], BIN);
Serial.print(" , ");
Serial.println(checksum1, BIN);
}
I wonder about that the same(!!) rfid tag has different values depending it gets read from RFID1 or RFID2:
RFID1 tag detected: 1000100 , 0
The tag's number is: 136 , 100 , 11100 , 1101011 , 11111011 , 11111011
RFID2 tag detected: 1000100 , 0
The tag's number is: 68 , 0 , 0 , 0 , 0 , 1000100

Answer 1

I use 10 RC522 together at the same time with Ardunio mega .
Try this example for 2 ncf reader, its work for me. I tested in Arduino Nano.
The readers share the pins for 3,3V, GND. SCD, MISO, MOSI, RST and have own pins for SDA. I don't use the IRQ pin.
#include <SPI.h>
#include <MFRC522.h>
#define RST_PIN 9 // Configurable, see typical pin layout above
#define SS1_PIN 10 // Configurable, see typical pin layout above
#define SS2_PIN 8 // Configurable, see typical pin layout above
MFRC522 mfrc522_1(SS1_PIN, RST_PIN); // Create MFRC522 instance
MFRC522 mfrc522_2(SS2_PIN, RST_PIN);
void setup() {
Serial.begin(9600); // Initialize serial communications with the PC
while (!Serial); // Do nothing if no serial port is opened (added for Arduinos based on ATMEGA32U4)
SPI.begin(); // Init SPI bus
mfrc522_1.PCD_Init(); // Init MFRC522
mfrc522_1.PCD_DumpVersionToSerial(); // Show details of PCD - MFRC522 Card Reader details
Serial.println(F("Scan PICC to see UID, SAK, type, and data blocks..."));
mfrc522_2.PCD_Init(); // Init MFRC522
mfrc522_2.PCD_DumpVersionToSerial(); // Show details of PCD - MFRC522 Card Reader details
}
void loop() {
// Look for new cards
if ( mfrc522_1.PICC_IsNewCardPresent() || mfrc522_2.PICC_IsNewCardPresent()) {
Serial.println(F("New card..."));
} else {
return;
}
// Select one of the cards
if ( ! mfrc522_1.PICC_ReadCardSerial() && ! mfrc522_2.PICC_ReadCardSerial()) {
Serial.println(F("Read..."));
return;
}
// Dump debug info about the card; PICC_HaltA() is automatically called
mfrc522_1.PICC_DumpToSerial(&(mfrc522_1.uid));
mfrc522_2.PICC_DumpToSerial(&(mfrc522_2.uid));
}

Answer 2

//Anti-collision, return tag serial number 4 bytes
status = myRFID2.AddicoreRFID_Anticoll(str1); // <<<< needs to be strl2