I have a Boarduino Duemilanove w/Atmega 328. I want to upload my program to it. I have W8.1 on my laptop.
The power green led is running and the red led is blinking. When I put the serial cable, but before I upload my program, the arduino.exe gives me the message:
"Arduino: 1.6.5 (Windows 8.1), Board: "Arduino Duemilanove or
Diecimila, ATmega328"
and
Sketch uses 1,030 bytes (3%) of program storage space. Maximum is
30,720 bytes. Global variables use 9 bytes (0%) of dynamic memory,
leaving 2,039 bytes for local variables. Maximum is 2,048 bytes.
and then
avrdude: ser_open(): can't open device "\.\COM2": Access is denied.
Problem uploading to board. See
http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.
This report would have more information with "Show verbose output
during compilation" enabled in File > Preferences."
anyone can help me please?.
I know this one is old but i had the same problem and for me it ended up being the cable. I found a smaller one to do the upload and it worked.
In the IDE, go to tools > board, then select your board. After that, you go to tools > port, and select the serial port or USB port the Arduino is hooked up to. If you are using a mac, the port name should be long, so look for USB in the name. On windows, it should say either COM5// or COM6// or something similar. If not, just play around with different ports and boards (in the ide selection) and see if one of the combinations works. You shouldn't need to play around with the board selection too much, but try different ports. One is bound to work.
Related
Few months ago, I bought cheap arduino nano from china. Instaled all the required drivers, and tried out my frirst program.
Now I tried to upload something new, and I get this error message:
avrdude: ser_open(): can't open device "\.\COM4": System can't find given file.
I also noticed, that Tools->Ports can not be clicked. The device does not even show up in device manager.
Any Ideas?
In my first program I did also set pin 0 and 1 (RX/TX) as outputs and used them to flash LEDs. I am aware, that this probably prevents new code from beeing uploded, but it should not prevent from the device from shoving up at all. The computer talking to the USB driver, not the microcontroller.
Go to Device Manager and find the Arduino COM Port
Go to the Advanced properties of the port
Set the port # to COM1
Then un-plug your USB and plug it back in.
My Arduino Uno was all set up and was working fine.
Project: Arduino controls a 9v motor depending on the command given. As the Arduino only provides 5v, I added a 9v battery to it through a transistor
I decided to add new code into the Arduino but when I tried it failed. I have uploaded code thousands of times before (successfully) all of a sudden the IDE keeps giving the following message
avrdude: ser_open(): can't open device ".\COM3": Access is denied.
I have looked up for a lot of solutions on this forum and elsewhere. Here are the things I have tried so far:
Changing the COM port
Disabling all the other devices CONNECTED to COM
Tightening the CONNECTIONS
Re installing all the drivers and the IDE
Rebooting the system
Using another laptop to upload code
All the above have given me the same output for some reason. The built in LED light and the power LED switch on when the board is connected to a power source (my laptop). Could the board have been damaged by any chance? How can I check if the board is spoilt? Should I buy a new board?
this may help;
remove the mcu from the board and connect the board to your PC.
try to open the com port.
if it opens, short TX pin to RX pin.
send some data and check if you are getting the data back. this way you can make sure your usb-ttl is not damaged.
With my verry limited experience with Arduino I've seen that the IDE sometimes resets the saved arduino on startup. Press extra -> Board -> yourboard and try again.
make sure you have the right ports COM1 and COM1
activate it too in arduino
Once it happened to me that a defective USB cable was the culprit. For one board it gave messages like
avrdude: stk500v2_ReceiveMessage(): timeout
But for another board I also got these messages "can't open device - access denied". It's always worth to try another cable.
I am trying to upload this firmware sck_beta_v0_8_6 via Arduino 1.0.5-r2.
I have chosen LilyPad Arduino USB as the board. The device is a Smart Citizen Kit Urban Shield v.1.1.
The upload fails with the following error message:
Found programmer: Id = "BÛR"; type =
Software Version = . ; Hardware Version = .
avrdude: error: buffered memory access not supported. Maybe it isn't
a butterfly/AVR109 but a AVR910 device?
What am I doing wrong?
Sometimes, a different USB cable will make all the difference. There is a wide range in the quality of cables on the market, and sometimes, you get one on the ragged edge of acceptable.
The Arduino lilypad seems to be particularly susceptible to this. Glad this helped.
Press the Reset Button before upload the code, until you hear the "unplug" sound (in windows). Open the IDE and try it again
I had the same error message trying to upload a sketch to an Arduino Leonardo board from a Levovo laptop using Arduino ver 1.0.6. Both Device Manager and Arduino showed the board connected on COM3. Arduino also gave an error message that COM3 was being used by another App. I tried changing USB cables but got the same message. What worked was changing the USB outlet from the top right rear on the Lenovo to the bottom right rear outlet. It connected on COM8 and I was able to upload the sketch. Understand there are speed differences between the two outlets. Now all I need to do is figure out why I cannot upload sketches to the same Leonardo board on my HP laptop with Windows 10 and the most recent Arduino version. Connects on COM6 but hangs up when uploading. (Note: Also had to edit some Arduino library files that worked on ver 1.0.6 but showed compile errors in the latest version.)
I had the same error, but I later found that I had the wrong Arduino type selected, instead of Nano I had Yun.
I had the same issue when trying to upload code into Arduino Micro ( Chinese clone ). Spending hours on Google, flashing new bootloader - still nothing. Physical reset and opening COM port with boundrate 1200 doesn't work. Why?
I HAVE ATMEGA168 INSTEAD OF ATMEGA32u4!
Google is telling, that Arduino Micro got Atmega32u4, but my clone got Atmega168! First of all, check what atmega type do you have by lookup on black soldered chip on Arduino.
So instead of choose "Arduino Micro" on "Board" menu, i choose Arduino Nano and everything works!
I get this same error, avrdude: error: buffered memory access not supported also with garbage-looking output with programmer id # with versions ., when I point avrdude at the serial port of the stock main firmware of my Leonardo-compatible breakout board instead of the serial port offered during the bootloader; it seems that the latter is what avrdude can program?
The normal initial output when actually connecting to the bootloader would be something like:
Connecting to programmer: .
Found programmer: Id = "CATERIN"; type = S
Software Version = 1.0; No Hardware Version given.
To get to the bootloader you can either
press the reset button (if you don't have a reset button, connecting reset to ground), or
briefly connect to the main firmware's serial port at 1200 bps and disconnect
The bootloader will present a different serial USB device than the main firmware's serial USB device, so it may get assigned a different serial port number in your OS, usually the next available one. For instance in Windows my Leonardo-compatible main firmware was assigned COM3 and the bootloader was assigned COM4.
A python script, courtesy of https://nicholaskell.wordpress.com/tag/leonardo/, for doing this serial 'knock':
reset.py:
#!/usr/bin/env python
import serial, sys
serialPort = sys.argv[1]
ser = serial.Serial(
port=serialPort,
baudrate=1200,
parity=serial.PARITY_NONE,
stopbits=serial.STOPBITS_ONE,
bytesize=serial.EIGHTBITS
)
ser.isOpen()
ser.close() # always close port
In Windows land, I have a cmd script for using this in a virtualenv
reset.cmd:
"C:\Program Files (x86)\Python37-32\Scripts\virtualenv.exe" pyreset_virtualenv
pyreset_virtualenv\Scripts\pip.exe install pyserial
pyreset_virtualenv\Scripts\python reset.py COM3
pause
adjust to suit your serial port and python path.
Either way, after getting the bootloader connected, you have a brief window of a couple of seconds where avrdude can connect to the new serial port to start programming before the bootloader will go into the main firmware again, at which point you'll have to do the reset again. So, once you figure out the bootloader serial port, you'll want to prepare the avrdude command line to run in advance, so you can launch it without delay after the reset.
While this answer isn't specific to the lilypad, you need to reset the board to write or read from/to the memory. However, If you are using avrdude in the terminal you must send a specific baudrate(1200 for the Leonardo) then close, wait 2 seconds, and open the port. At that point you can read and write to and from your Arduino. I achieved this using python.
Along the lines of:
Import serial
Import time
Import os
Seri=serial.Serial(yourConnectedPort, specificBaudRate)
Seria.close()
time.sleep(2)
Seri.open()
os.system(your avrdude command)
This is the main error that I get when I try to run my ARDUINO program. The full list of errors is as follows:
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_getsync(): timeout communicating with programmer
My code is as follows:
int led=13;
void setup()
{
pinMode(13,OUTPUT);
}
void loop()
{
digitalWrite(13,HIGH);
delay(1000);
digitalWrite(13,LOW);
delay(1000);
}
I have tried updating the drivers (they are fully updated) and downloading some programs. I have Windows 7 and my arduino is a MEGA 2560. It shows up in the Device Manager and all of my connections are correct. The green PWR light is on and so is the flashing L light. The RX and TX lights flash when I update. I have tried almost everything on the web. What is the problem?
Another possible reason for this error for the Mega 2560 is if your code has three exclamation marks in a row. Perhaps in a recently added string.
3 bang marks in a row causes the Mega 2560 bootloader to go into Monitor mode from which it can not finish programming.
"!!!" <--- breaks Mega 2560 bootloader.
To fix, unplug the Arduino USB to reset the COM port and then recompile with only two exclamation points or with spaces between or whatever. Then reconnect the Arduino and program as usual.
Yes, this bit me yesterday and today I tracked down the culprit. Here is a link with more information: http://forum.arduino.cc/index.php?topic=132595.0
The error message basically means that the programmer is unable to contact the bootloader on the device; the code you're trying to upload has no bearing on the problem.
What causes this can be numerous and varied, some possible issues:
UART communications
Blinking is happening, so hopefully you aren't using the wrong port. It might be worth checking again though, sometimes USB COM devices install on strange port numbers.
Connect TX to RX (and disconnect them from the AVR if possible) then open a terminal on the COM port, you should see characters echoed if you type them. If you don't, something is wrong up-stream of the chip, it could be the communications chip (I think the Arduino 2560 uses a secondary AVR instead of an FTDI for some reason, so that could be broken, either its software or hardware)
ATmega* bootloader
The AVR is not executing the bootloader for some reason. If the programmer is not resetting the micro before attempting to connect, this might be the reason. Try to reset the AVR (press and release the button) while the programmer is attempting to connect. Sometimes software that runs in a tight loop will prevent the bootloader from connecting.
Barring that, the fuses might have gotten messed up or the code erased. You would need to reflash the bootloader and proper fuses, again, see the appropriate info page for your device.
Arduino Mega 2560 only: ATmega8U/16U software
Might not be working and would need reprogramming. See the Programming section on the info page, you will need the firmware and Atmel-compatible DFU (device firmware update) software on your computer to reflash the target.
Hardware damage to the board, AVR(s), or FTDI chip
You're hosed; need a new chip.
Check this forum post for some more ideas.
I got this error because I didn't specify the correct programmer in the avrdude command line. You have to specify "-c arduino" if you are using an Arduino board.
This example command reads the status of the hfuse:
avrdude -c arduino -P /dev/ttyACM0 -p atmega328p -U hfuse:r:-:h
To my humble understanding, this error arises in different scenarios:
you have selected the wrong port or you haven't at all. go to tools > ports and select the com port with your Arduino connected to.
you have selected the wrong board. go to tools > board and look for the right board.
Do you have one of these Arduino replicas or you don't have the boot-loader installed on the microcontroller? I don't know the solution to this! if you know please edit my post and add the instructions.
(windows only) you don't have the right drivers installed. you need to update them manually.
sometimes when you have wires connected to the board this happens. you need to separate the board from any breadboard or wires you have installed and try uploading again. It seems pins 0 (RX) and 1 (TX), which can be used for serial communication, are problematic and better to be free while uploading the code.
Sometimes it happens randomly for no specific reason!
There are all kinds of solutions all over the internet, but sometimes hard to tell the difference between magic! Maybe the Arduino team should think of better compiler errors to help users differentiate between these different causes.
The same problem happened to me and none of the solutions above worked. What happened was that I was using an Arduino UNO and everything was fine, but when I bought an Arduino Mega 2560, no matter what sketch I tried to upload I got the error:
avrdude: stk500v2_ReceiveMessage(): timeout
And it was just on one of my windows computers and the other one was just ok out of the box.
Solution:
What solved my problem was to go to tools > boards > Boards Manager... and then on the top left of the opened windows select updatable in the Type section. Then select the items in the list and press update on the right.
I'm not sure if this will solve everyone's problem, but it at least solved mine.
Open Terminal and type:
$ sudo usermod -a -G dialout
(This command is optional)
$ **sudo chmod a+rw /dev/ttyACM0**
(This command must succeed)
This isn't really a fixing solution but it may help others. Unlike Nick had said for me it was due to code in my program. I have the mega ADK model. The issue was tied to a switch statement for processing and parsing the returned byte[] from the usb connection to the Android. Its very strange because it would compile perfectly every time but would fail as the OP had stated. I commented it out and it worked fine.
I was running this code from Arduino setup , got same error resolve after changing
serial port to COM13
GO TO Option
tool>> serial port>> COM132
If you use the ino command line:
ino upload
it can be because you use the arduino software at the same time, try to kill it.
I've connected to USB port directly in my laptop and timeout issue has been resolved.
Previously tried by port replicator, but it did not even recognized arduino, thus I chosen wrong port - resulting in timeout message.
So make sure that it is visible by your OS.
Ensure the serial monitor is not running and nothing is reading/writing dev/tty/S0 (or whichever port you're using), which may cause uploading interference.
I had the same problem, and in my case, the solution was updating the usb-serial driver using windows update on windows 10 device's manager. There was no need to download a especific driver, I just let windows update find a suitable driver.
I faced same problem. but Root cause of issue. Incorrect communication was set and thats why I occurred Communication timeout.
Solution: If you connected to laptop through USB port.
Change Port as USB. Please follow steps
Open Arduino-IDE
Go to Menu "Tools --> Port" and Select option "USB" { for me its showing as /dev/ttyUSB0 }
It working fine for me.
Something not yet mentioned is that this message also appears when the baudrate is not properly set... for Arduino, it is generally 115200.
My aurdino mega 2560 returned same error. It seems the problem exists in unofficial clones. The issue solved by pressing reset button just before uploading starts, as advertised in following video.
https://www.youtube.com/watch?v=tAzjO4v7oF4&list=LLDn5ewJDzz53IiwWmZTgQnQ&index=1
I have a number of Windows 2000 systems that we are trying to use to program the new Arduino Uno and Mega devices. These boards now come with a USB connection, an upgrade from the prior FTDI. I'm not able to download the Arduino code into the board from a Windows 2000 system
The supplied drivers are *.inf files that modify the standard USB driver that comes with Windows (in this case Windows 2000).
I go through the process of setting the port, setting the device and doing the download. The download fails, and the apparent error is that the PC can not communicate with the board. I've checked the port, adjusted the baud rates, etc. I've even moved the port number from a high port number (ie COM12) to a lower port (COM2) without any success. I do see activity on the rec/xmt lights on the Arduino board, so some type of data is being sent and received.
I'm looking for:
Someone who has been able to download files from Windows 2000 to the Arduino
or
A way to shim inside the USB driver to be able to watch the traffic going up and down to the board so I can continue to debug this.
or
Some general tips for things to look at in the .inf file that need to be set/not set to make it work on Windows 2000.
I know the boards work I've used them on a different set of Windows XP systems. So I know to some extent the install is good and that most of what I have works.
Full dumps can be found on the Arduino forum, http://www.arduino.cc/cgi-bin/yabb2/YaBB.pl?num=1291090110/.
This is the information produced by the AVRDude program while it's trying to download the code.
this could be a long shot, but I jsut recentlz had problems uploading too. Fist of all, how long is the USB cabele you are uploading from? Mine in one case was too long and th arduino woul lose sync. Secondly, and this might just be a silly oversight (like i did) do you have things wired in the digital pin 0 and 1? These are used for the communication, and if there is anything else plugged in to them the upload will also fail.
As I said, long shot but those were two errors I had.