What's the maximum length of an HTTP GET request?
Is there a response error defined that the server can/should return if it receives a GET request that exceeds this length?
This is in the context of a web service API, although it's interesting to see the browser limits as well.
The limit is dependent on both the server and the client used (and if applicable, also the proxy the server or the client is using).
Most web servers have a limit of 8192 bytes (8 KB), which is usually configurable somewhere in the server configuration. As to the client side matter, the HTTP 1.1 specification even warns about this. Here's an extract of chapter 3.2.1:
Note: Servers ought to be cautious about depending on URI lengths above 255 bytes, because some older client or proxy implementations might not properly support these lengths.
The limit in Internet Explorer and Safari is about 2 KB, in Opera about 4 KB and in Firefox about 8 KB. We may thus assume that 8 KB is the maximum possible length and that 2 KB is a more affordable length to rely on at the server side and that 255 bytes is the safest length to assume that the entire URL will come in.
If the limit is exceeded in either the browser or the server, most will just truncate the characters outside the limit without any warning. Some servers however may send an HTTP 414 error.
If you need to send large data, then better use POST instead of GET. Its limit is much higher, but more dependent on the server used than the client. Usually up to around 2 GB is allowed by the average web server.
This is also configurable somewhere in the server settings. The average server will display a server-specific error/exception when the POST limit is exceeded, usually as an HTTP 500 error.
You are asking two separate questions here:
What's the maximum length of an HTTP GET request?
As already mentioned, HTTP itself doesn't impose any hard-coded limit on request length; but browsers have limits ranging on the 2 KB - 8 KB (255 bytes if we count very old browsers).
Is there a response error defined that the server can/should return if it receives a GET request exceeds this length?
That's the one nobody has answered.
HTTP 1.1 defines status code 414 Request-URI Too Long for the cases where a server-defined limit is reached. You can see further details on RFC 2616.
For the case of client-defined limits, there isn't any sense on the server returning something, because the server won't receive the request at all.
Browser limits are:
Browser Address bar document.location
or anchor tag
---------------------------------------------------
Chrome 32779 >64k
Android 8192 >64k
Firefox >64k >64k
Safari >64k >64k
Internet Explorer 11 2047 5120
Edge 16 2047 10240
Want more? See this question on Stack Overflow.
A similar question is here: Is there a limit to the length of a GET request?
I've hit the limit and on my shared hosting account, but the browser returned a blank page before it got to the server I think.
Technically, I have seen HTTP GET will have issues if the URL length goes beyond 2000 characters. In that case, it's better to use HTTP POST or split the URL.
As already mentioned, HTTP itself doesn't impose any hard-coded limit on request length; but browsers have limits ranging on the 2048 character allowed in the GET method.
Yes. There isn't any limit on a GET request.
I am able to send ~4000 characters as part of the query string using both the Chrome browser and curl command.
I am using Tomcat 8.x server which has returned the expected 200 OK response.
Here is the screenshot of a Google Chrome HTTP request (hiding the endpoint I tried due to security reasons):
RESPONSE
Related
I want to ask some question about the following quote taken from Head First Servlets and JSP, Second Edition book:
The total amount of characters in a GET is really limited (depending
on the server). If the user types, say, a long passage into a “search”
input box, the GET might not work.
Why is the total amount of characters in a GET limited?
How can I learn about the total amount of character in a Get?
When I said a long text into any input box, and GET is not working.
How many solution do I have to fix this problem.
Why is the get method limited?
There is no specific limit to the length of a GET request. Different servers can have different limits. If you need to send more data to the server, use POST instead of GET. A recommended minimum to be supported by servers and browsers is 8,000 bytes, but this is not required.
RFC 7230's Section 3.1.1 "Request Line" says
HTTP does not place a predefined limit on the length of a request-line, as described in Section 2.5. A server that receives a method longer than any that it implements SHOULD respond with a 501 (Not Implemented) status code. A server that receives a request-target longer than any URI it wishes to parse MUST respond with a 414 (URI Too Long) status code (see Section 6.5.12 of RFC7231).
Various ad hoc limitations on request-line length are found in practice. It is RECOMMENDED that all HTTP senders and recipients support, at a minimum, request-line lengths of 8000 octets.
Section 2.5 "Conformance and Error Handling" says
HTTP does not have specific length limitations for many of its protocol elements because the lengths that might be appropriate will vary widely, depending on the deployment context and purpose of the implementation. Hence, interoperability between senders and recipients depends on shared expectations regarding what is a reasonable length for each protocol element. Furthermore, what is commonly understood to be a reasonable length for some protocol elements has changed over the course of the past two decades of HTTP use and is expected to continue changing in the future.
and RFC 7231's Section 6.5.12 "414 URI Too Long" says
The 414 (URI Too Long) status code indicates that the server is
refusing to service the request because the request-target (Section
5.3 of [RFC7230]) is longer than the server is willing to interpret.
This rare condition is only likely to occur when a client has
improperly converted a POST request to a GET request with long query
information, when the client has descended into a "black hole" of
redirection (e.g., a redirected URI prefix that points to a suffix of
itself) or when the server is under attack by a client attempting to
exploit potential security holes.
The 'get'-data is send in the query string - which also has a maximum length.
You can do all kind of things with the query string, e.g. bookmark it. Would you really like to bookmark a real huge text?
It is possible to configure moste servers to use larger length - some clients will accept them, some will throw errors.
"Note: Servers ought to be cautious about depending on URI lengths above 255 bytes, because some older client or proxy implementations might not properly support these lengths." HTTP 1.1 specification chapter 3.2.1:.
There is also a status code "414 Request-URI Too Long" - if you get this you will know that you have put to many chars in the get. (If you hit the server limit, if the client limit is lower then the server limit each browser will react in it's own way).
Generally it would be wise to set a limit for each data being send to a server - just if someones tries to make huge workload or slow down the server (e.g. send a huge file - 1 server connection is used. slow down the transmission, make additional sends - at some point the server wil have a lot of connections open. Use multiple clients and you have an attack scenario on a server).
I understand that one can set Accept-Ranges: none on the server to advise the client not to attempt a range request.
I am wondering if there is a way to tell a browser not to attempt a range request without having to make any changes on the server.
For instance, is there a setting in Chrome or Firefox that I can toggle to deter my browser from making range requests?
You answered the question in the first sentence.
The relevant RFC is 7233, Hypertext Transfer Protocol (HTTP/1.1): Range Requests:
2.3. Accept-Ranges
A client MAY generate
range requests without having received this header field for the
resource involved.
A server that does not support any kind of range request for the
target resource MAY send
Accept-Ranges: none
to advise the client not to attempt a range request.
If you mean you want to know how to disable range requests in a browser altogether, consult the specific browser's documentation. A quick web search yielded no options for me to do this for common browsers.
What is the specification for maximum data size one can send with HTTP POST method?
Quite amazing how all answers talk about IIS, as if that were the only web server that mattered. Even back in 2010 when the question was asked, Apache had between 60% and 70% of the market share. Anyway,
The HTTP protocol does not specify a limit.
The POST method allows sending far more data than the GET method, which is limited by the URL length - about 2KB.
The maximum POST request body size is configured on the HTTP server and typically ranges from
1MB to 2GB
The HTTP client (browser or other user agent) can have its own limitations. Therefore, the maximum POST body request size is min(serverMaximumSize, clientMaximumSize).
Here are the POST body sizes for some of the more popular HTTP servers:
Nginx (largest web server market share as of April 2019) - default 1MB, no practical maximum (2**63)
Apache - maximum 2GB, no default documented
IIS - default 28.6MB for the request length, 2048 bytes for the query string; maximum undocumented
InfluxDB - default ~25MB, maximum undocumented
EDIT (2019) This answer is now pretty redundant but there is another answer with more relevant information.
It rather depends on the web server and web browser:
Internet explorer All versions 2GB-1
Mozilla Firefox All versions 2GB-1
IIS 1-5 2GB-1
IIS 6 4GB-1
Although IIS only support 200KB by default, the metabase needs amending to increase this.
http://www.motobit.com/help/scptutl/pa98.htm
The POST method itself does not have any limit on the size of data.
There is no limit according to the HTTP protocol itself, but implementations will have a practical upper limit. I have sent data exceeding 4 GB using POST to Apache, but some servers did have a limit of 4 GB at the time.
POST allows for an arbitrary length of data to be sent to a server, but there are limitations based on timeouts/bandwidth etc.
I think basically, it's safer to assume that it's not okay to send lots of data.
Different IIS web servers can process different amounts of data in the 'header', according to this (now deleted) article; http://classicasp.aspfaq.com/forms/what-is-the-limit-on-form/post-parameters.html;
Note that there is no limit on the
number of FORM elements you can pass
via POST, but only on the aggregate
size of all name/value pairs. While
GET is limited to as low as 1024
characters, POST data is limited to 2
MB on IIS 4.0, and 128 KB on IIS 5.0.
Each name/value is limited to 1024
characters, as imposed by the SGML
spec. Of course this does not apply to
files uploaded using
enctype='multipart/form-data' ... I
have had no problems uploading files
in the 90 - 100 MB range using IIS
5.0, aside from having to increase the server.scriptTimeout value as well as
my patience!
In an application I was developing I ran into what appeared to be a POST limit of about 2KB. It turned out to be that I was accidentally encoding the parameters into the URL instead of passing them in the body. So if you're running into a problem there, there is definitely a very small limit on the size of POST data you can send encoded into the URL.
HTTP may not have an upper limit, but webservers may have one. In ASP.NET there is a default accept-limit of 4 MB, but you (the developer/webmaster) can change that to be higher or lower.
Is there an accepted maximum allowed size for HTTP headers? If so, what is it? If not, is this something that's server specific or is the accepted standard to allow headers of any size?
No, HTTP does not define any limit. However most web servers do limit size of headers they accept. For example in Apache default limit is 8KB, in IIS it's 16K. Server will return 413 Entity Too Large error if headers size exceeds that limit.
Related question: How big can a user agent string get?
As vartec says above, the HTTP spec does not define a limit, however many servers do by default. This means, practically speaking, the lower limit is 8K. For most servers, this limit applies to the sum of the request line and ALL header fields (so keep your cookies short).
Apache 2.0, 2.2: 8K
nginx: 4K - 8K
IIS: varies by version, 8K - 16K
Tomcat: varies by version, 8K - 48K (?!)
It's worth noting that nginx uses the system page size by default, which is 4K on most systems. You can check with this tiny program:
pagesize.c:
#include <unistd.h>
#include <stdio.h>
int main() {
int pageSize = getpagesize();
printf("Page size on your system = %i bytes\n", pageSize);
return 0;
}
Compile with gcc -o pagesize pagesize.c then run ./pagesize. My ubuntu server from Linode dutifully informs me the answer is 4k.
Here is the limit of most popular web server
Apache - 8K
Nginx - 4K-8K
IIS - 8K-16K
Tomcat - 8K – 48K
Node (<13) - 8K; (>13) - 16K
HTTP does not place a predefined limit on the length of each header
field or on the length of the header section as a whole, as described
in Section 2.5. Various ad hoc limitations on individual header
field length are found in practice, often depending on the specific
field semantics.
HTTP Header values are restricted by server implementations. Http specification doesn't restrict header size.
A server that receives a request header field, or set of fields,
larger than it wishes to process MUST respond with an appropriate 4xx
(Client Error) status code. Ignoring such header fields would
increase the server's vulnerability to request smuggling attacks
(Section 9.5).
Most servers will return 413 Entity Too Large or appropriate 4xx error when this happens.
A client MAY discard or truncate received header fields that are
larger than the client wishes to process if the field semantics are
such that the dropped value(s) can be safely ignored without changing
the message framing or response semantics.
Uncapped HTTP header size keeps the server exposed to attacks and can bring down its capacity to serve organic traffic.
Source
RFC 6265 dated 2011 prescribes specific limits on cookies.
https://www.rfc-editor.org/rfc/rfc6265
6.1. Limits
Practical user agent implementations have limits on the number and
size of cookies that they can store. General-use user agents SHOULD
provide each of the following minimum capabilities:
o At least 4096 bytes per cookie (as measured by the sum of the
length of the cookie's name, value, and attributes).
o At least 50 cookies per domain.
o At least 3000 cookies total.
Servers SHOULD use as few and as small cookies as possible to avoid
reaching these implementation limits and to minimize network
bandwidth due to the Cookie header being included in every request.
Servers SHOULD gracefully degrade if the user agent fails to return
one or more cookies in the Cookie header because the user agent might
evict any cookie at any time on orders from the user.
--
The intended audience of the RFC is what must be supported by a user-agent or a server. It appears that to tune your server to support what the browser allows you would need to configure 4096*50 as the limit. As the text that follows suggests, this does appear to be far in excess of what is needed for the typical web application. It would be useful to use the current limit and the RFC outlined upper limit and compare the memory and IO consequences of the higher configuration.
I also found that in some cases the reason for 502/400 in case of many headers could be because of a large number of headers without regard to size.
from the docs
tune.http.maxhdr
Sets the maximum number of headers in a request. When a request comes with a
number of headers greater than this value (including the first line), it is
rejected with a "400 Bad Request" status code. Similarly, too large responses
are blocked with "502 Bad Gateway". The default value is 101, which is enough
for all usages, considering that the widely deployed Apache server uses the
same limit. It can be useful to push this limit further to temporarily allow
a buggy application to work by the time it gets fixed. Keep in mind that each
new header consumes 32bits of memory for each session, so don't push this
limit too high.
https://cbonte.github.io/haproxy-dconv/configuration-1.5.html#3.2-tune.http.maxhdr
If you are going to use any DDOS provider like Akamai, they have a maximum limitation of 8k in the response header size. So essentially try to limit your response header size below 8k.
is there any limitation for url?how many characters can take the maximum url? thank u.
This depends on the browser you are using.
From RFC 2616 (rfc2616) - Hypertext Transfer Protocol -- HTTP/1.1
The HTTP protocol does not place any a
priori limit on the length of a
URI. Servers MUST be able to handle
the URI of any resource they serve,
and SHOULD be able to handle URIs of
unbounded length if they provide
GET-based forms that could generate
such URIs. A server SHOULD return
414 (Request-URI Too Long) status if a
URI is longer than the server can
handle (see section 10.4.15).
Note: Servers ought to be cautious about depending on URI
lengths
above 255 bytes, because some older client or proxy
implementations might not properly support these lengths.
Maximum URL length is 2,083 characters in Internet Explorer
Microsoft Internet Explorer has a
maximum uniform resource locator (URL)
length of 2,083 characters. Internet
Explorer also has a maximum path
length of 2,048 characters. This limit
applies to both POST request and GET
request URLs.
If you are using the GET method, you
are limited to a maximum of 2,048
characters, minus the number of
characters in the actual path.
However, the POST method is not
limited by the size of the URL for
submitting name/value pairs. These
pairs are transferred in the header
and not in the URL.
From http://www.boutell.com/newfaq/misc/urllength.html
Firefox (Browser)
After 65,536 characters, the location bar no longer displays the URL in Windows Firefox
1.5.x. However, longer URLs will work. I stopped testing after 100,000 characters.
Safari (Browser)
At least 80,000 characters will work. I stopped testing after 80,000 characters.
Opera (Browser)
At least 190,000 characters will work. I stopped testing after 190,000 characters. Opera > 9 for Windows continued to display a fully editable, copyable and pasteable URL in the
location bar even at 190,000 characters.
Apache (Server)
My early attempts to measure the maximum URL length in web browsers bumped into a server > URL length limit of approximately 4,000 characters, after which Apache produces a "413
Entity Too Large" error. I used the current up to date Apache build found in Red Hat
Enterprise Linux 4. The official Apache documentation only mentions an 8,192-byte limit
on an individual field in a request.
Microsoft Internet Information Server
The default limit is 16,384 characters (yes, Microsoft's web server accepts longer URLs
than Microsoft's web browser). This is configurable.
Perl HTTP::Daemon (Server)
Up to 8,000 bytes will work. Those constructing web application servers with Perl's
HTTP::Daemon module will encounter a 16,384 byte limit on the combined size of all HTTP
request headers. This does not include POST-method form data, file uploads, etc., but it > does include the URL. In practice this resulted in a 413 error when a URL was
significantly longer than 8,000 characters. This limitation can be easily removed. Look
for all occurrences of 16x1024 in Daemon.pm and replace them with a larger value. Of
course, this does increase your exposure to denial of service attacks.
Check this thread of Stackoverflow What is the maximum length of a URL in different browsers?
Maximum URL length is 2083 characters in Internet Explorer
http://support.microsoft.com/kb/208427
Maximum URL length is 65000 characters in Mozila Firefox
http://support.mozilla.com/tiki-view_forum_thread.php?comments_offset=0&comments_threadId=0&comments_parentId=153230&comments_threshold=0&thread_sort_mode=commentDate_asc&forumId=1&time_control=3600
it depends on browser : for ie max characters is 2083 - http://support.microsoft.com/kb/208427