I have TCP client application and trying to connect with Server located at remote machine.
I am able to connect it.
when I Send Message Called Hello packet the Server should respond with data and time info.
but to my surprise recv returns 0 at client.
since I can't Debug code at Server.
I am not sure but may be there is problem in encoding the message format hello packet at th client upon receiving the wrong packet server is clsoing the connection
I wanted to confirm the meaning of following sequence is
I got following info from wire shark
src IP------>dst ip SYN
dst ip ----->src ip SYN,ACK
src IP------>dst ip ACK
src IP------>dst ip continuation or non http traffic "Hello Packet"
dst ip------>ACK
dst ip------>FIN, ACK
Does this means Server is closing the connection once it receives the hello packet?
Yeah, the FIN,ACK sequence is sent by one of the entity connected when they want to close the connection
Related
My unit is supposed to send CSR request to a CA server and get the new certificate. When checked packets captured via Wireshark, TCP packet is sent with SYN but received RST,ACK. When tried to identify the root cause for this, I see many possibilities in the web. Now, how how to identify the actual reason for this failure?
when a TCP client wants to establish a tcp connection with a tcp server
it needs to send SYN and then ACK
while tcp server only sends SYN/ACK
so they are different
but , after the 3_way handshaking,
is this connection symmetric, namely, are TCP client and server in equal status
for example, after the 3-way handshake, usually the client send packet first,
can TCP server send packet first?
No, the procedure is not different at all, but instead of sending a SYN then an ACK in two different packets, the servers concatenate them by sending them via a single packet!
In the other hand, remember always that the client/server nomenclature is relative. The server is the party that remains in listening mode, while the client is the party that initiates the connection ...
After the establishment of the connection, both parties are equivalent (same status as you said: ESTABLISHED). For that reason, both can send the FIN statement to close the connection ...
After the connection is established, both ends are indeed "symmetric". Who sends first is decided by the underlying protocol and differes amongst them.
For example, HTTP starts with the GET <path> HTTP/1.0 command, while other protocols let the server give a greeting line first, and only then the client sends its request.
So in general, both ends are free to send their stuff first.
I use raw socket to build a tcp client program and run it on machine A
and I run a regular tcp server program on machine B
the raw socket-based client program first send a SYN packet
and then it receives a SYN/ACK packet from the remote tcp server
then the kernel of machine A sends a RST to the remote tcp server
the sequence number and ack-sequence number is fine
what are potential reasons?
and how to deal with it? thanks!
BTW: I used tcpdump to capture packets on the remote machine B
and it shows "TCP port numbers reused" for the SYN packet from client,
actually before the client send the SYN, I used
netstat -tnp
to check on-going tcp sessions, and it shows nothing
This is perfectly normal. If a machine receives a SYN/ACK packet it doesn't expect, it should respond with a RST to let the other side know that it has no knowledge of or interest in that connection. The kernel sent a RST because that's what it's supposed to do -- it has no idea what your program is doing.
If you're trying to run your own TCP stack on a machine that already has a TCP stack, you'll have to prevent the regular TCP stack from responding to machines your stack is trying to talk to -- otherwise, they'll be talking to two TCP stacks which can't possibly work.
The SYN packet has the same source dest IP address & port with the established connection, so what will happen in this case?
The server will silently drop the packet since it already has a connection in the ESTABLISHED state, one of the four values from (client-ip, src-port, server-ip, dest-port) must be different for the new SYN to be accepted.
The server will attempt a new connection.
in tech terms it will send a syn,ack packet and wait for the client to finish the tcp handshake
and open the connection.
http://en.wikipedia.org/wiki/Transmission_Control_Protocol
will explain the process alot better than me.
the server will send some information to identify the connection in its syn,ack packet.
and that information is used to keep that connection seperate from others.
Most the time, the ports will not be the same
but when it is, it can cause problems with low grade nat routers,
They try to rewrite that ports that are used, and can get the connections confused.
Some things look strange to me:
What is the distinction between 0.0.0.0, 127.0.0.1, and [::]?
How should each part of the foreign address be read (part1:part2)?
What does a state Time_Wait, Close_Wait mean?
etc.
Could someone give a quick overview of how to interpret these results?
0.0.0.0 usually refers to stuff listening on all interfaces.
127.0.0.1 = localhost (only your local interface)
I'm not sure about [::]
TIME_WAIT means both sides have agreed to close and TCP
must now wait a prescribed time before taking the connection
down.
CLOSE_WAIT means the remote system has finished sending
and your system has yet to say it's finished.
I understand the answer has been accepted but here is some additional information:
If it says 0.0.0.0 on the Local Address column, it means that port is listening on all 'network interfaces' (i.e. your computer, your modem(s) and your network card(s)).
If it says 127.0.0.1 on the Local Address column, it means that port is ONLY listening for connections from your PC itself, not from the Internet or network. No danger there.
If it displays your online IP on the Local Address column, it means that port is ONLY listening for connections from the Internet.
If it displays your local network IP on the Local Address column, it means that port is ONLY listening for connections from the local network.
Foreign Address - The IP address and port number of the remote computer to which the socket is connected. The names that corresponds to the IP address and the port are shown unless the -n parameter is specified. If the port is not yet established, the port number is shown as an asterisk (*). (from wikipedia)
What is the distinction between 0.0.0.0, 127.0.0.1, and [::]?
0.0.0.0 indicates something that is listening on all interfaces on the machine.
127.0.0.1 indicates your own machine.
[::] is the IPv6 version of 0.0.0.0
My machine also shows *:\* for UDP which shows that UDP connections don't really have a foreign address - they receive packets from any where. That is the nature of UDP.
How should each part of the foreign address be read (part1:part2)?
part1 is the hostname or IP addresspart2 is the port
127.0.0.1 is your loopback address also known as 'localhost' if set in your HOSTS file. See here for more info: http://en.wikipedia.org/wiki/Localhost
0.0.0.0 means that an app has bound to all ip addresses using a specific port. MS info here: http://support.microsoft.com/default.aspx?scid=kb;en-us;175952
'::' is ipv6 shorthand for ipv4 0.0.0.0.
Send-Q is the amount of data sent by the application, but not yet acknowledged by the other side of the socket.
Recv-Q is the amount of data received from the NIC, but not yet consumed by the application.
Both of these queues reside in kernel memory.
There are guides to help you tweak these kernel buffers, if you are so inclined. Although, you may find the default params do quite well.
This link has helped me a lot to interpret netstat -a
A copy from there -
TCP Connection States
Following is a brief explanation of this handshake. In this context the "client" is the peer requesting a connection and the "server" is the peer accepting a connection. Note that this notation does not reflect Client/Server relationships as an architectural principal.
Connection Establishment
The client sends a SYN message which contains the server's port and the client's Initial Sequence Number (ISN) to the server (active open).
The server sends back its own SYN and ACK (which consists of the client's ISN + 1).
The Client sends an ACK (which consists of the server's ISN + 1).
Connection Tear-down (modified three way handshake).
The client sends a FIN (active close). This is a now a half-closed connection. The client no longer sends data, but is still able to receive data from the server. Upon receiving this FIN, the server enters a passive close state.
The server sends an ACK (which is the clients FIN sequence + 1)
The server sends its own FIN.
The client sends an ACK (which is server's FIN sequence + 1). Upon receiving this ACK, the server closes the connection.
A half-closed connection can be used to terminate sending data while sill receiving data. Socket applications can call shutdown with the second argument set to 1 to enter this state.
State explanations as shown in Netstat:
State Explanation
SYN_SEND Indicates active open.
SYN_RECEIVED Server just received SYN from the client.
ESTABLISHED Client received server's SYN and session is established.
LISTEN Server is ready to accept connection.
NOTE: See documentation for listen() socket call. TCP sockets in listening state are not shown - this is a limitation of NETSTAT. For additional information, please see the following article in the Microsoft Knowledge Base:
134404 NETSTAT.EXE Does Not Show TCP Listen Sockets
FIN_WAIT_1 Indicates active close.
TIMED_WAIT Client enters this state after active close.
CLOSE_WAIT Indicates passive close. Server just received first FIN from a client.
FIN_WAIT_2 Client just received acknowledgment of its first FIN from the server.
LAST_ACK Server is in this state when it sends its own FIN.
CLOSED Server received ACK from client and connection is closed.
For those seeing [::] in their netstat output, I'm betting your machine is running IPv6; that would be equivalent to 0.0.0.0, i.e. listen on any IPv6 address.