Why is the IP called a connectionless protocol? If so, what is the connection-oriented protocol then?
Thanks.
Update - 1 - 20:21 2010/12/26
I think, to better answer my question, it would be better to explain what "connection" actually means, both physically and logically.
Update - 2 - 9:59 AM 2/1/2013
Based on all the answers below, I come to the feeling that the 'connection' mentioned here should be considered as a set of actions/arrangements/disciplines. Thus it's more an abstract concept rather than a concrete object.
Update - 3 - 11:35 AM 6/18/2015
Here's a more physical explanation:
IP protocol is connectionless in that all packets in IP network are routed independently, they may not necessarily go through the same route, while in a virtual circuit network which is connection oriented, all packets go through the same route. This single route is what 'virtual circuit' means.
With connection, because there's only 1 route, all data packets will arrive in the same order as they are sent out.
Without connection, it is not guaranteed all data packets will arrive
in the same order as they are sent out.
Update - 4 - 9:55 AM 2016/1/20/Wed
One of the characteristics of connection-oriented is that the packet order is preserved. TCP use a sequence number to achieve that but IP has no such facility. Thus TCP is connection-oriented while IP is connection-less.
The basic idea is pretty simple: with IP (on its own -- no TCP, UDP, etc.) you're just sending a packet of data. You simply send some data onto the net with a destination address, but that's it. By itself, IP gives:
no assurance that it'll be delivered
no way to find out if it was
nothing to let the destination know to expect a packet
much of anything else
All it does is specify a minimal packet format so you can get some data from one point to another (e.g., routers know the packet format, so they can look at the destination and send the packet on its next hop).
TCP is connection oriented. Establishing a connection means that at the beginning of a TCP conversation, it does a "three way handshake" so (in particular) the destination knows that a connection with the source has been established. It keeps track of that address internally, so it can/will/does expect more packets from it, and be able to send replies to (for example) acknowledge each packet it receives. The source and destination also cooperate to serial number all the packets for the acknowledgment scheme, so each end knows whether packets it sent were received at the other end. This doesn't involve much physically, but logically it involves allocating some memory on both ends. That includes memory for metadata like the next packet serial number to use, as well as payload data for possible re-transmission until the other side acknowledges receipt of that packet.
TCP/IP means "TCP over IP".
TCP
--
IP
TCP provides the "connection-oriented" logic, ordering and control
IP provides getting packets from A to B however it can: "connectionless"
Notes:
UDP is connection less but at the same level as TCP
Other protocols such as ICMP (used by ping) can run over IP but have nothing to do with TCP
Edit:
"connection-oriented" mean established end to end connection. For example, you pick up the telephone, call someone = you have a connection.
"connection-less" means "send it, see what happens". For example, sending a letter via snail mail.a
So IP gets your packets from A to B, maybe, in any order, not always eventually. TCP sorts them out, acknowledges them, requests a resends and provides the "connection"
Connectionless means that no effort is made to set up a dedicated end-to-end connection, While Connection-Oriented means that when devices communicate, they perform handshaking to set up an end-to-end connection.
IP is an example of the Connectionless protocols , in this kind of protocols you usually send informations in one direction, from source to destination without checking to see if the destination is still there, or if it is prepared to receive the information . Connectionless protocols (Like IP and UDP) are used for example with the Video Conferencing when you don't care if some packets are lost , while you have to use a Connection-Oriented protocol (Like TCP) when you send a File because you want to insure that all the packets are sent successfully (actually we use FTP to transfer Files). Edit :
In telecommunication and computing in
general, a connection is the
successful completion of necessary
arrangements so that two or more
parties (for example, people or
programs) can communicate at a long
distance. In this usage, the term has
a strong physical (hardware)
connotation although logical
(software) elements are usually
involved as well.
The physical connection is layer 1 of
the OSI model, and is the medium
through which the data is transfered.
i.e., cables
The logical connection is layer 3 of
the OSI model, and is the network
portion. Using the Internetwork
Protocol (IP), each host is assigned a
32 bit IP address. e.g. 192.168.1.1
TCP is the connection part of TCP/IP. IP's the addressing.
Or, as an analogy, IP is the address written on the envelope, TCP is the postal system which uses the address as part of the work of getting the envelope from point A to point B.
When two hosts want to communicate using connection oriented protocol, one of them must first initiate a connection and the other must accept it. Logically a connection is made between a port in one host and other port in the other host. Software in one host must perform a connect socket operation, and the other must perform an accept socket operation. Physically the initiator host sends a SYN packet, which contains all four connection identifying numbers (source IP, source port, destination IP, destination port). The other receives it and sends SYN-ACK, the initiator sends an ACK, then the connection are established. After the connection established, then the data could be transferred, in both directions.
In the other hand, connectionless protocol means that we don't need to establish connection to send data. It means the first packet being sent from one host to another could contain data payloads. Of course for upper layer protocols such as UDP, the recipient must be ready first, (e.g.) it must perform a listen udp socket operation.
The connectionless IP became foundation for TCP in the layer above
In TCP, at minimal 2x round trip times are required to send just one packet of data. That is : a->b for SYN, b->a for SYN-ACK, a->b for ACK with DATA, b->a for ACK. For flow rate control, Nagle's algorithm is applied here.
In UDP, only 0.5 round trip times are required : a->b with DATA. But be prepared that some packets could be silently lost and there is no flow control being done. Packets could be sent in the rate that are larger than the capability of the receiving system.
In my knowledge, every layer makes a fool of the one above it. The TCP gets an HTTP message from the Application layer and breaks it into packets. Lets call them data packets. The IP gets these packets one by one from TCP and throws it towards the destination; also, it collects an incoming packet and delivers it to TCP. Now, TCP after sending a packet, waits for an acknowledgement packet from the other side. If it comes, it says the above layer, hey, I have established a connection and now we can communicate! The whole communication process goes on between the TCP layers on both the sides sending and receiving different types of packets with each other (such as data packet, acknowledgement packet, synchronization packet , blah blah packet). It uses other tricks (all packet sending) to ensure the actual data packets to be delivered in ordered as they were broken and assembled. After assembling, it transfers them to the above application layer. That fool thinks that it has got an HTTP message in an established connection but in reality, just packets are being transferred.
I just came across this question today. It was bouncing around in my head all day and didn't make any sense. IP doesn't handle transport. Why would anyone even think of IP as connectionless or connection oriented? It is technically connectionless because it offers no reliability, no guaranteed delivery. But so is my toaster. My toaster offers no guaranteed delivery, so why not call aa toaster connectionless too?
In the end, I found out it's just some stupid title that someone somewhere attached to IP and it stuck, and now everyone calls IP connectionless and has no good reason for it.
Calling IP connectionless implies there is another layer 3 protocol that is connection oriented, but as far as I know, there isn't and it is just plain stupid to specify that IP is connectionless. MAC is connectionless. LLC is connectionless. But that is useless, technically correct info.
Related
According to my knowledge if an internet application has to be designed, we should use either a connection-oriented service or connection-less service, but not both.
Internet's connection oriented service is TCP and connection-less service is UDP, and both resides in the transport layer of Internet Protocol stack.
Internet's only network layer is IP, which is a connection-less service. So it means whatever application we design it eventually uses IP to transmit the packets.
Connection-oriented services use the same path to transmit all the packets, and connection-less does not.
Therefore my problem is
if a connection oriented application has been designed, it should transmit the packets using the same path. But IP breaks that rule by using different routes.So how do both TCP and IP work together in this sense? It totally confuses me.
You, my friend, are confusing the functionality of two different layers.
TCP is connection oriented in the sense that there's a connection establishment, between the two ends where they may negotiate different things like congestion-control mechanism among other things.
The transport layer protocols' general purpose is to provide process-to-process delivery meaning that it doesn't know anything about routes; how your packets reach the end system is beyond their scope, they're only concerned with how packets are being transmitted between the two end PROCESSES.
IP, on the other hand, the Network layer protocol for the Internet, is concerned with data-delivery between end-systems yet it's connection-less, it maintains no connection so each packet is handled independently of the other packets.
Leaving your system, each router will choose the path that it sees fit for EACH packet, and this path may change depending on availability/congestion.
How does that answer your question?
TCP will make sure packets reach the other process, it won't care HOW they got there.
IP, on the other hand, will not care if they reach the other end at all, it'll simply forward each different packet according to what it sees most fit for a particular packet.
Note:
Let's assume that IP was connection-oriented, would that mean packets would follow the same-path?
Not necessarily, it depends on what the word 'connection' at this layer means, if it means negotiating certain options related to security, for instance, you may still have all your packets being forwarded through different routes over the Internet.
EDIT:
Not to confuse you though, most connection-oriented services at the network-layer and below mean that the connection, when established, also establishes a virtual-path that all 'packets' must follow, for further information read about:
Virtual circuit and frame-relay networks
This link answers your question pretty well http://www.tcpipguide.com/free/t_ConnectionOrientedandConnectionlessProtocols-3.htm
Some people consider this (TCP) to be like a “simulation” of circuit-switching at higher network layers; this is perhaps a bit of a dubious analogy. Even though a TCP connection can be used to send data back and forth between devices, all that data is indeed still being sent as packets; there is no real circuit between the devices. This means that TCP must deal with all the potential pitfalls of packet-switched communication, such as the potential for data loss or receipt of data pieces in the incorrect order.
The TCP protocol deals with the problem of IP packets arriving out of order or being lost, to give you the feeling they arrive through a single FIFO channel. Yes, TCP is smart enough to do that, there's no need for a dedicated underlying channel.
The TCP protocal is implemented by the sending/receiving machines, once the packets leave the sending machine, the routers they travel along know nothing about TCP, they just use IP to get the packets from the source the to destination. Then, it is the destination machines job to, using TCP, make sure that all the packets arrive and that they arrive in the correct order. The internet itself doesn't know anything about TCP, it's just a layer (often software) that gives connection to a connectionless medium (the internet).
So onces a packet leaves a destination, it can go along any path (mostly) as long as it gets to the desintation, regardless of the higher level protocol (such as TCP or UDP).
I mean, it's a bit more complicated then that, but as far as I can remember that's the general Idea.
Refer my short points properly,
1) Connection oriented means ==> reserving resources(buffer,cpu,bandwidth etc.)..but "Where??".(where resources are reserved?? This where is reason of your confusion, so following is ans.).
2) Connection oriented at Transport Layer means ==> Reserving the resources at Both End processes/Ports.(Since TCP is a transport layer,then its responsibility is to reserve the resources at both end processes only,irrespective of whats happening in the intermediate path.)
3) Connection oriented at Network Layer means ==> Reserving the resources at Network Layers.(Now In the whole journey of a packet from source to destination, Network layer is found at all intermediate routers too(but not transport layer). Hence if any protocol at Network layer is connection oriented then,its responsibility is to reserve resources at all intermediate routeres too i.e. all packets will have to follow same intermediate path, But IP is connection less hence,intermediate resources will not be reserved. i.e journey of a packets may follow different paths etc.)
#CONCLUSION:==> Intermediate path is decided by Network Layer, hence if IP then paths may be different.(IP may contain TCP),But TCP is responsible for Resource reservation at both End processes ,irrespective of Intermediate path of packet.
router works on three layers only (physical , data link and Network layers) , so routers will take decision depending only on the info. of network layer (IP protocol ) hence there is no information available about its TCP or UDP at the router
Using the TCP/IP protocol, given a connection between a client and a server, are the packets sent by the client to the server always received in the same order they were sent?
For example, if the client sends 3 packets of data, A, B and C, will the server always receive A first followed by B and C or is it possible for the server to receive C first, followed by A and B?
At IP level, packets may arrive in any order (if they arrive). At TCP level, the data stream is guaranteed to be ordered in the same manner on both ends.
That means yes, the server will always receive A then B then C. As long as you are using TCP.
When using TCP, data is received by the destination application in the same order as it is sent by the source application.
See the following for more details:
http://en.wikipedia.org/wiki/Transmission_Control_Protocol#Data_transfer
TCP is a transmission protocol, and it transmits data by sending the data out in IP packets over the underlying IP network. TCP is responsible for ensuring the correct transmission of the data, which includes ordering the arriving packets, re-requesting missing ones and discarding duplicates.
TCP as such does not expose any notion of "packet" to the user; the fact that the data is chunked into IP packets is a detail of the "over IP" implementation. A different implementation, e.g. TCP-over-bicycle-courier, might employ an entirely different scheme.
It cannot happen that you receive data in a different order on the application side over a TCP socket.
It may happen that packets are received in a different order by the networking layer of the OS, but TCP makes it a requirement that the upper levels get data in order. It is the OS' role to ask again for unreceived fragments etc and assemble these fragments. So, you need not worry.
UDP, on the other hand, offers no such guarantee.
The server (as the physical NIC of the machine) might receive them in any order. Your OS might receive them in any order again - that will mostly (but not allways) be the order of physical reception. Your client application is guaranteed to receive them in correct order, thats a property of TCP
In general, packets will be received in the same order they are transmitted. But the network may drop or reorder packets. For example, packets may take different routes and arrive out of order. Packets may be lost or even duplicated on the network. The TCP implementation is responsible for retransmitting packets that are lost, acknowledging packets that are received, ignoring duplicated packets, all with the objective of accurately reconstructing the transmitted byte stream at the receiver.
At the application level, you send a stream of bytes and receive a stream of bytes. TCP does whatever is needed to ensure the received stream of bytes is identical to the sent stream of bytes, regardless of what happens to the packets on the network.
What is the difference between TCP and UDP?
I know that TCP is used in the case of non-time critical applications, and UDP is used for games or applications that require fast transmission of data. I know that TCP is used for HTTP, HTTPs, FTP, SMTP, and Telnet. I know that UDP is used for DNS and DHCP.
But why? What characteristics of TCP and UDP make it useful for their respective use cases?
TCP is a connection oriented stream over an IP network. It guarantees that all sent packets will reach the destination in the correct order. This imply the use of acknowledgement packets sent back to the sender, and automatic retransmission, causing additional delays and a general less efficient transmission than UDP.
UDP is a connection-less protocol. Communication is datagram oriented. The integrity is guaranteed only on the single datagram. Datagrams reach destination and can arrive out of order or don't arrive at all. It is more efficient than TCP because it uses non ACK. It's generally used for real time communication, where a little percentage of packet loss rate is preferable to the overhead of a TCP connection.
In certain situations UDP is used because it allows broadcast packet transmission. This is sometimes fundamental in cases like DHCP protocol, because the client machine hasn't still received an IP address (this is the DHCP negotiaton protocol purpose) and there won't be any way to establish a TCP stream without the IP address itself.
From the Skullbox article:
TCP (Transmission Control Protocol) is the most commonly used protocol on the Internet.
The reason for this is because TCP offers error correction. When the TCP protocol is used there is a "guaranteed delivery." This is due largely in part to a method called "flow control." Flow control determines when data needs to be re-sent, and stops the flow of data until previous packets are successfully transferred. This works because if a packet of data is sent, a collision may occur. When this happens, the client re-requests the packet from the server until the whole packet is complete and is identical to its original.
UDP (User Datagram Protocol) is anther commonly used protocol on the Internet. However, UDP is never used to send important data such as webpages, database information, etc; UDP is commonly used for streaming audio and video. Streaming media such as Windows Media audio files (.WMA) , Real Player (.RM), and others use UDP because it offers speed! The reason UDP is faster than TCP is because there is no form of flow control or error correction. The data sent over the Internet is affected by collisions, and errors will be present. Remember that UDP is only concerned with speed. This is the main reason why streaming media is not high quality.
1) TCP is connection oriented and reliable where as UDP is connection less and unreliable.
2) TCP needs more processing at network interface level where as in UDP it’s not.
3) TCP uses, 3 way handshake, congestion control, flow control and other mechanism to make sure the reliable transmission.
4) UDP is mostly used in cases where the packet delay is more serious than packet loss.
Think of TCP as a dedicated scheduled UPS/FedEx pickup/dropoff of packages between two locations, while UDP is the equivalent of throwing a postcard in a mailbox.
UPS/FedEx will do their damndest to make sure that the package you mail off gets there, and get it there on time. With the post card, you're lucky if it arrives at all, and it may arrive out of order or late (how many times have you gotten a postcard from someone AFTER they've gotten home from the vacation?)
TCP is as close to a guaranteed delivery protocol as you can get, while UDP is just "best effort".
Reasons UDP is used for DNS and DHCP:
DNS - TCP requires more resources from the server (which listens for connections) than it does from the client. In particular, when the TCP connection is closed, the server is required to remember the connection's details (holding them in memory) for two minutes, during a state known as TIME_WAIT_2. This is a feature which defends against erroneously repeated packets from a preceding connection being interpreted as part of a current connection. Maintaining TIME_WAIT_2 uses up kernel memory on the server. DNS requests are small and arrive frequently from many different clients. This usage pattern exacerbates the load on the server compared with the clients. It was believed that using UDP, which has no connections and no state to maintain on either client or server, would ameliorate this problem.
DHCP - DHCP is an extension of BOOTP. BOOTP is a protocol which client computers use to get configuration information from a server, while the client is booting. In order to locate the server, a broadcast is sent asking for BOOTP (or DHCP) servers. Broadcasts can only be sent via a connectionless protocol, such as UDP. Therefore, BOOTP required at least one UDP packet, for the server-locating broadcast. Furthermore, because BOOTP is running while the client... boots, and this is a time period when the client may not have its entire TCP/IP stack loaded and running, UDP may be the only protocol the client is ready to handle at that time. Finally, some DHCP/BOOTP clients have only UDP on board. For example, some IP thermostats only implement UDP. The reason is that they are built with such tiny processors and little memory that the are unable to perform TCP -- yet they still need to get an IP address when they boot.
As others have mentioned, UDP is also useful for streaming media, especially audio. Conversations sound better under network lag if you simply drop the delayed packets. You can do that with UDP, but with TCP all you get during lag is a pause, followed by audio that will always be delayed by as much as it has already paused. For two-way phone-style conversations, this is unacceptable.
One of the differences is in short
UDP : Send message and dont look back if it reached destination, Connectionless protocol
TCP : Send message and guarantee to reach destination, Connection-oriented protocol
TCP establishes a connection before the actual data transmission takes place, UDP does not. In this way, UDP can provide faster delivery. Applications like DNS, time server access, therefore, use UDP.
Unlike UDP, TCP uses congestion control. It responses to the network load. Unlike UDP, it slows down when network congestion is imminent. So, applications like multimedia preferring constant throughput might go for UDP.
Besides, UDP is unreliable, it doesn't react on packet losses. So loss sensitive applications like multimedia transmission prefer UDP. However, TCP is a reliable protocol, so, applications that require reliability such as web transfer, email, file download prefer TCP.
Besides, in today's internet UDP is not as welcoming as TCP due to middle boxes. Some applications like skype fall down to TCP when UDP connection is assumed to be blocked.
Run into this thread and let me try to express it in this way.
TCP
3-way handshake
Bob: Hey Amy, I'd like to tell you a secret
Amy: OK, go ahead, I'm ready
Bob: OK
Communication
Bob: 'I', this is the first letter
Amy: First letter received, please send me the second letter
Bob: ' ', this is the second letter
Amy: Second letter received, please send me the third letter
Bob: 'L', this is the third letter
After a while
Bob: 'L', this the third letter
Amy: Third letter received, please send me the fourth letter
Bob: 'O', this the forth letter
Amy: ...
......
4-way handshake
Bob: My secret is exposed, now, you know my heart.
Amy: OK. I have nothing to say.
Bob: OK.
UDP
Bob: I LOVE U
Amy received: OVI L E
TCP is more reliable than UDP with even message order guaranteed, that's no doubt why UDP is more lightweight and efficient.
The Law of Leaky Abstractions
by Joel Spolsky
http://www.joelonsoftware.com/articles/LeakyAbstractions.html
Short and simple differences between Tcp and Udp protocol:
1) Tcp - Transmission control protocol and Udp - User datagram protocol.
2) Tcp is reliable protocol, Where as Udp is a unreliable protocol.
3) Tcp is a stream oriented, where as Udp is a message oriented protocol.
4) Tcp is a slower than Udp.
This sentence is a UDP joke, but I'm not sure that you'll get it. The below conversation is a TCP/IP joke:
A: Do you want to hear a TCP/IP joke?
B: Yes, I want to hear a TCP/IP joke.
A: Ok, are you ready to hear a TCP/IP joke?
B: Yes, I'm ready to hear a TCP/IP joke.
A: Well, here is the TCP/IP joke.
A: Did you receive a TCP/IP joke?
B: Yes, I **did** receive a TCP/IP joke.
TCP and UDP are transport layer protocol, Layer 4 protocol in OSI(open systems interconnection model). The main difference along with pros and cons are as following.
TCP
PROS:
Acknowledgment
Guaranteed Delivery
Connection based
Ordered packets
Congestion control
CONS:
Larger Packet
More bandwidth
Slower
Statefull
Consume memory
UDP
PROS:
Packets are smaller
Consume less bandwidth
Faster
Stateless
CONS:
No acknowledgment
No guaranteed delivery
Connectionless
No congestion control
No order packet
TLDR;
TCP - stream-oriented, requires a connection, reliable, slow
UDP - message-oriented, connectionless, unreliable, fast
Before we start, remember that all disadvantages of something are a continuation of its advantages. There only a right tool for a job, no panacea. TCP/UDP coexist for decades, and for a reason.
TCP
It was designed to be extremely reliable and it does its job very well. It's so complex because it accomplishes a hard task: providing a reliable transport over the unreliable IP protocol.
Since all TCP's complex logic is encapsulated into the network stack, you are free from doing lots of laborious, error-prone low-level stuff in the application layer.
When you send data over TCP, you write a stream of bytes to the socket at the sender side where it gets broken into packets, passed down the stack and sent over the wire. On the receiver side packets get reassembled again into a continous stream of bytes.
Maintaining this nice abstraction has a cost in terms of complexity and performance. If the 1st packet from the byte stream is lost, the receiver will delay processing of subsequent packets even those have already arrived (the so-called "head of line blocking").
In addition, in order to be reliable, TCP implements this:
TCP requires an established connection, which requires 3 round-trips ("infamous" 3-way handshake)
TCP has a feature called "slow start" when it gradually ramps up the transmission rate after establishing a connection to allow a receiver to keep up with data rate
Every sent packet has to be acknowledged or else a sender will stop sending more data
And on and on and on...
All this is exacerbated in slow unreliable wireless networks because TCP was designed for wired networks where delays are predictable and packet loss is not so common. In addition, like many people already mentioned, for some things TCP just doesn't work at all (DHCP). However, where relevant, TCP still does its work exceptionally well.
Using a mail analogy a TCP session is similar to telling a story to your secretary who breaks it into mails and sends over a crappy mail service to a publisher. On the other side another secretary assembles mails into a single piece of text. Some mails get lost, some get corrupted, so a very complex procedure is required for reliable delivery and your 10-page story can take a long time to reach your publisher.
UDP
UDP, on the other hand, is message-oriented, so a receiver writes a message (packet) to the socket and then it gets transmitted to a receiver as-is, without any splitting/assembling in the transport layer.
Compared to TCP, its specification is very straightforward. Essentially, all it does for you is adding a checksum to the packet so a receiver can detect its corruption. Everything else must be implemented by you, a software developer. Now read the voluminous TCP spec and try thinking of re-implementing even a small subset of it.
Some people went this way and got very decent results, to the point that HTTP/3 uses QUIC - a protocol based on UDP. However, this is more of an exception. Common applications of UDP are audio/video streaming and conferencing applications like Skype, Zoom or Google Hangout where loosing packets is not so important compared to a delay introduced by TCP.
Simple Explanation by Analogy
TCP is like this.
Imagine you have a pen-pal on Mars (we communicated with written letters back in the good ol' days before the internet).
You need to send your pen pal the seven habits of highly effective people. So you decide to send it in seven separate letters:
Letter 1 - Be proactive
Letter 2 - Begin with the end in mind...
etc.
etc..Letter 7 - Sharpen the Saw
Requirements:
You want to make sure that your pen pal receives all your letters - in order and that they arrive perfectly. If your pen pay receives letter 7 before letter 1 - that's no good. if your pen pal receives all letters except letter 3 - that also is no good.
Here's how we ensure that our requirements are met:
Confirmation Letter: So your pen pal sends a confirmation letter to say "I have received letter 1". That way you know that your pen pal has received it. If a letter does not arrive, or arrives out of order, then you have to stop, and go back and re-send that letter, and all subsequent letters.
Flow Control: Around the time of Xmas you know that your pen pal will be receiving a lot of mail, so you slow down because you don't want to overwhelm your pen pal. (Your pen pal sends you constant updates about the number of unread messages there are in penpal's mailbox - if your pen pal says that the inbox is about to explode because it is so full, then you slow down sending your letters - because your pen pal won't be able to read them.
Perfect arrival. Sometimes while you send your letter in the mail, it can get torn, or a snail can eat half of it. How do you know that all your letter has arrived in perfect condition? Well your pen pal will give you a mechanism by which you can check whether they've got the full letter and that it was the exactly the letter that you sent. (e.g. via a word count etc. ). a basic analogy.
I know the difference between the two on a technical level.
But in real life, can anyone provide examples (the more the better) of applications (uses) of TCP and UDP to demonstrate the difference?
UDP: Anything where you don't care too much if you get all data always
Tunneling/VPN (lost packets are ok - the tunneled protocol takes care of it)
Media streaming (lost frames are ok)
Games that don't care if you get every update
Local broadcast mechanisms (same application running on different machines "discovering" each other)
TCP: Almost anything where you have to get all transmitted data
Web
SSH, FTP, telnet
SMTP, sending mail
IMAP/POP, receiving mail
EDIT: I'm not going to bother explaining the differences, since you state that you already know and every other answer explains it anyway :)
UDP is mailing a letter at the post office.
TCP is mailing a letter with a return receipt at the post office, except that the post master will organize the letters in-order-of mailing and only deliver them in-order.
Well, it was an attempt anyway.
TCP:
World Wide Web(HTTP)
E-mail (SMTP TCP)
File Transfer Protocol (FTP)
Secure Shell (SSH)
UDP:
Domain Name System (DNS)
Streaming media applications such as movies
Online multiplayer games
Voice over IP (VoIP)
Trivial File Transfer Protocol (TFTP)
REAL TIME APPLICATION FOR TCP:
Email:
Reason: suppose if some packet(words/statement) is missing we cannot understand the content.It should be reliable.
REAL TIME APPLICATION FOR UDP:
video streaming:
* **Reason: ***suppose if some packet(frame/sequence) is missing we can understand the content.Because video is collection of frames.For 1 second video there should be
25 frames(image).Even though we can understand some frames are missing due to our imagination skills. Thats why UDP is used for video streaming.
The classic standpoint is to consider TCP as safe and UDP as unreliable.
But when TCP-IP protocols are used in safety critical applications,
TCP is not recommended because it can stop on error for multiple reasons.
Whereas UDP lets the application software deal with errors, retransmission timers, etc.
Moreover, TCP has more processing overhead than UDP.
Currently, UDP is used in aircraft controls and flight instruments,
in the ARINC 664 standard also named AFDX (Avionics Full-Duplex Switched Ethernet).
In ARINC 664, TCP is optional but UDP is used with the RTOS (real time operating systems) designed for the ARINC 653 standard (high reliability control software in civil aircrafts).
For more information about real time controls using IP and UDP in AFDX,
you can read the pages 27 to 50 in
http://www.afdx.com/pdf/AFDX_Training_October_2010_Full.pdf
TCP
I will not send data anymore until i get an acknowledgment.
this process is slow
It is used for security purpose
example: web, sending mail, receiving mail etc
UDP
Here i have no headache with acknowledgment.
this process is faster but here data can be lost .
example : video streaming , online games etc
TCP + UDP = SMTP(example : mobile,telephone)
TCP guarantees (in-order) packet delivery. UDP doesn't.
TCP - used for traffic that you need all the data for. i.e HTML, pictures, etc.
UDP - used for traffic that doesn't suffer much if a packet is dropped, i.e. video & voice streaming, some data channels of online games, etc.
TCP is a connection oriented protocol, It establishes a path, or a virtual connection all the way through switches routers proxies etc and then starts any communication. Various mechanisms like routing djikstras shortest path algorithm exist to establish the virtual end to end connection. So it finds itself used while browsing HTML and other pages, making payments and web applications in general.
UDP is a connectionless protocol - it simply has a destination and nodes simply pass it along if it comes as best as they can. So packets arriving out of order, along various routes etc are common. So Instant messengers and similar software developers think UDP an ideal solution.
In real life if you want to throw data in the net, without worrying about time taken to reach, order of reaching use UDP. If you want a solid path before you start throwing packets, and want same order and latency for your data packets use TCP - I will use UDP for Torrents and TCP for PayPal!
TCP :
Transmission Control Protocol is a connection-oriented protocol, which means that it requires handshaking to set up end-to-end communications. Once a connection is set up, user data may be sent bi-directionally over the connection.
Reliable – Strictly only at transport layer, TCP manages message acknowledgment, retransmission and timeout. Multiple attempts to deliver the message are made. If it gets lost along the way, the server will re-request the lost part. In TCP, there's either no missing data, or, in case of multiple timeouts, the connection is dropped. (This reliability however does not cover application layer, at which a separate acknowledgement flow control is still necessary)
Ordered – If two messages are sent over a connection in sequence, the first message will reach the receiving application first. When data segments arrive in the wrong order, TCP buffers delay the out-of-order data until all data can be properly re-ordered and delivered to the application.
Heavyweight – TCP requires three packets to set up a socket connection, before any user data can be sent. TCP handles reliability and congestion control.
Streaming – Data is read as a byte stream, no distinguishing indications are transmitted to signal message (segment) boundaries.
Applications of TCP
World Wide Web, email, remote administration, and file transfer rely on TCP.
UDP :
User Datagram Protocol is a simpler message-based connectionless protocol. Connectionless protocols do not set up a dedicated end-to-end connection. Communication is achieved by transmitting information in one direction from source to destination without verifying the readiness or state of the receiver.
Unreliable – When a UDP message is sent, it cannot be known if it will reach its destination; it could get lost along the way. There is no concept of acknowledgment, retransmission, or timeout.
Not ordered – If two messages are sent to the same recipient, the order in which they arrive cannot be predicted.
Lightweight – There is no ordering of messages, no tracking connections, etc. It is a small transport layer designed on top of IP.
Datagrams – Packets are sent individually and are checked for integrity only if they arrive. Packets have definite boundaries which are honored upon receipt, meaning a read operation at the receiver socket will yield an entire message as it was originally sent.
No congestion control – UDP itself does not avoid congestion. Congestion control measures must be implemented at the application level.
Broadcasts – being connectionless, UDP can broadcast - sent packets can be addressed to be receivable by all devices on the subnet.
Multicast – a multicast mode of operation is supported whereby a single datagram packet can be automatically routed without duplication to very large numbers of subscribers.
Applications of UDP
Numerous key Internet applications use UDP, including: the Domain Name System (DNS), where queries must be fast and only consist of a single request followed by a single reply packet, the Simple Network Management Protocol (SNMP), the Routing Information Protocol (RIP) and the Dynamic Host Configuration Protocol (DHCP).
Voice and video traffic is generally transmitted using UDP. Real-time video and audio streaming protocols are designed to handle occasional lost packets, so only slight degradation in quality occurs, rather than large delays if lost packets were retransmitted. Because both TCP and UDP run over the same network, many businesses are finding that a recent increase in UDP traffic from these real-time applications is hindering the performance of applications using TCP, such as point of sale, accounting, and database systems. When TCP detects packet loss, it will throttle back its data rate usage. Since both real-time and business applications are important to businesses, developing quality of service solutions is seen as crucial by some.
Some VPN systems such as OpenVPN may use UDP while implementing reliable connections and error checking at the application level.
TCP is appropriate when you have to move a decent amount of data (> ~1 kB), and you require all of it to be delivered. Almost all data that moves across the internet does so via TCP - HTTP, SMTP, BitTorrent, SSH, etc, all use TCP.
UDP is appropriate when you have small messages which you can afford to lose, and would like to send them as efficiently as possible. One reason you might be able to afford to lose them is because you can re-send them if they get lost. The main example on the internet is DNS - DNS consists of small queries saying things like "what is the IP number for stackoverflow.com?", and the responses are correspondingly small. Computers make a lot of these queries, so they should be made efficiently, but if they get lost en route, it's easy to time out and re-send them.
TCP guarantees packet delivery AND order. Order is almost as important as the delivery in the first place when reconstructing data for files such as executables, etc.
UDP does not guarantee delivery NOR order. Packets can arrive (or not!) in any order.
Common uses for TCP include file transfer where the integrity of the packets is paramount. Voice/video applications can afford to lose some data while still maintaining acceptable quality, and so usually use UDP.
One additional thought on some of the comments above that talks about ordered delivery.... It must be clarified that the destination computer may receive packets out of order on the wire, but the TCP at the destination is responsible for "rearranging out-of-order data" before passing it on to the upper layers of the stack. When you say TCP guarantees ordered packet delivery, what that means is it will deliver packets in correct order to the upper layers of the stack.
SCTP vs TCP vs UDPServices/Features SCTP TCP UDP
Connection-oriented yes yes no
Full duplex yes yes yes
Reliable data transfer yes yes no
Partial-reliable data transfer optional no no
Ordered data delivery yes yes no
Unordered data delivery yes no yes
Flow control yes yes no
Congestion control yes yes no
ECN capable yes yes no
Selective ACKs yes optional no
Preservation of message boundaries yes no yes
Path MTU discovery yes yes no
Application PDU fragmentation yes yes no
Application PDU bundling yes yes no
Multistreaming yes no no
Multihoming yes no no
Protection against SYN flooding attacks yes no n/a
Allows half-closed connections no yes n/a
Reachability check yes yes no
Psuedo-header for checksum no (vtags) yes yes
Time wait state vtags 4-tuple n/a
Since tcp usages are pretty straightforward from other answers, I'll mention some interesting UDP use-cases:
1)DHCP - Dynamic Host Configuration Protocol, which is being used in order to dynamically assign IP address and some other network configuration to the connecting devices. In simple words, this protocol allows you just connect to the network cable(or wifi) and start using the internet, without any additional configurations. DHCP uses UDP protocol. Since the settings request message is being broadcasted from the host and there is no way to establish a TCP connection with DHCP server(you don't know it's address) it's impossible to use TCP instead.
2)Traceroute - well-known network diagnostic tool which allows you to explore which path in the network your datagram passes to reach it's destination(and how much time it takes). By default, it works by sending UDP datagram with unlikely destination port number(ranging from 33434 to 33534) to the destination with the ttl(time-to-live) field set to 1. When the router somewhere in the network gets such datagram - it finds out that the datagram is expired. Then, the router drops the datagram and sends to the origin of the datagram an ICMP(Internet Control Message Protocol) error message indicating that the datagram's ttl was expired and containing router's name and IP address. Each time the host sends datagrams with higher and higher TTL, thus increasing the network part which it succeeds to overcome and getting new ICMP messages from new routers. When it eventually reaches it's destination(datagrams TTL is big enough to allow it),- the destination host sends 'Destination port unreachable' ICMP message to the origin host. This way, Traceroute knows that the destination was reached. Since the TCP guarantees segments delivery it would be at least inefficient to use it instead of UDP which, in turn, allows datagram to be just dropped without any resend attempts(resend is implemented on the higher level, with continuously increasing TTL as described above).
TCP: will get there in meaningful order
UDP: god knows (maybe)
UDP is applied a lot in games or other Peer-to-peer setups because it's faster and most of the time you don't need the protocol itself to make sure everything gets to the destination in the original order (UDP does not garantee packet delivery or delivery order).
Web traffic on the other hand is over TCP. (I'm not sure here but I think it has to do with the way the HTTP protocol is built)
Edited because I failed at UDP.
Real life examples of both TCP and UDP
tcp -> a phone call, sms or anything specific to destination
UDP -> a FM radio channel (AM), Wi-Fi.
I was configuring IPtable yesterday. My colleague just asked me this question, and I couldn't anwser. I realized that I'm a much better developper than sysadmin and need to improve that.
So what are they? What are they for? Cons/Pros (if it's relevant).
These are like basic questions.
UDP :: User Datagram Protocol
1) No end to end Connection between to machines (may be in local network or somewhere in the internet).
2) The data received at the receiver end is not in stream as in TCP but as a complete block of data.
3) At the transport layer no packet order check is performed. That is in case of any error in the received packet, the receiver will not ask for resending the same packet to the sender.
4) Because of the above behaviour no sending buffers are required at the sender's end.
5) As no end to end connection is estld. and there are no handshakings required, UDP are pretty much faster but less reliable than TCP. Thus mostly used in gaming and DNS etc..
6) No acknowledgement required to be sent after recieiving packets.
TCP :: Transmission control Protocol
1) End to end Connection is maintained between to machines (may be in local network or somewhere in the internet).
2) The data received at the receiver end is a stream in TCP. Thus, when we do network programming for servers we first parse the header first and then depending upon the size mentioned in the header we obtain that much more number of bytes from the buffer.
3) Error checking and sequence number are all done. Thus in case any packet is received out of order (rarely) or is erred than that packet is made to resend. Also, lots of other protocols are involved for flow control (end to end flow control).
4) As connection establishment , handshaking and acknowledgement is to be done TCP are basically slower in operation than UDP.(Not significantly I believe)
5) Lots of protocols uses TCP as underlying transport protocol. HTTP,FTP,TELNET etc..
6) The communication procedure involves:
Server:: 1) Socket Open
2) Socket Bind
3) Socket Listen
4) Socket Accept
5) Socket Send/Recv
Client :: 1) Socket Open
2) Socket Connect
3) Socket Send/Recv
There are lots of other differeces also..but the above being the most common ones.
TCP is a reliable protocol which ensures that your packets reach their destination and is used in applications where all data must me trasfered accurately between parties. TCP requires both parties to negotiate a connection before data transfer can start and it is a resilient protocol since it will repeatedly resend a packet until that packet is received by the intended recipient.
UDP is unreliable in a sense that it allows some packets to be lost in transit. Some applications of UDP are found in movie streaming where you can actually afford to lose a frame and not jeopardize movie quality. UDP does not need binding between the two parties and is often looked at as a light alternative to TCP.
A nice table is found here:TCP vs UDP
P.R.'s answer is mostly correct, but incomplete.
TCP is a reliable, connected stream protocol. Its view of data is that of a bidirectional stream of bytes between hosts: whatever bytes you send will arrive at the other end in the same order, at least as far as the application is concerned (the OS will rearrange packets if needed).
UDP is an unconnected datagram protocol. Its view of data is that of discrete datagrams, or messages, with no guarantee that these messages actually reach their recipient, or that they arrive in the order they were sent. It does guarantee that if a message arrives, it arrives in its entirety and without modification.
This website probably offers the simplest explanation to the actual difference of UDP and TCP. From implementation point of view, see this question.
For short answer: TCP works kind of like registered letter when UDP is kind of like ordinary letter - with the latter you never know whether the recipient got the packet you sent.
There are loads of helpful comparisons
chris is right!
One fancy link dropping out of google is: http://www.skullbox.net/tcpudp.php