How do I use winzip command line with include full path information ? I know I can do this under Winzip GUI but how to do it using cmd ? Also, is there a way to zip selected specific folders only ? Thanks
Tried GUI and it is working very slow
Winzip command line doesnt seem to zip selected folders - either parent folders or specific subfolders
I am using winzip 27 command line and this is the syntax I am using:
wzzip -a -e0 -k -P -r -yx "C:\Users\source\to\save\zipfile.zip" "C:\example"
This stores files and folder timestamps underneath C:\example. But since I have enabled -P -r, I want to store the timestamps of the upper folder, C:\example folder. How can I do that ? Does anyone have suggestions?
Also, how do I specify the path for a mapped network drive? Thanks!
Related
Writing a beginner shell script and it's asking for to locate and verify if a file under a specific name is located within my home directory but I'm not sure what command would best fit that.
To find any file in linux, use this command:
find . -name file_name
point means current directory
you can change it to /home/
thanks
I was trying to deploy my application on Ubuntu 16.04. So i made a package with the following hierarchy -
Package
|
----bin
|
-----application
-----application.sh
-----Qt
|
-----necessary qt libraries
-----platforms
Here is the application.sh file -
#!/bin/sh
export LD_LIBRARY_PATH=`pwd`/Qt
./application
When i execute the application.sh file, it shows me that it cant find the libQt5MultimediaWidgets.so.5 file. But its in the Qt folder. Also when i print the ldd application from the application.sh file after exporting LD_LIBRARY_PATH it gives me following output -
Please check the marked parts. Can anyone please explain why the libraries from the Qt folder are not found even after exporting the LD_LIBARRY_PATH?
Edit:
So as suggested by #Zang, i have checked the debug log and here it is -
Please check the marked parts.
It seems like its actually trying the actual libQt5MultimediaWidgets.so and then report that its unable to find it. Can anyone please help me understand whats happening here?
Edit-2: As per suggestion from #Tarun, i have ran ls -al on my Qt folder. Here is the output -
All files in Your Qt directory are actually simlinks to non-existing files in the same directory, therefore they cannot be found.
If you look at the output of your ls -al
These are soft links that you have. Your softlink libQt5MultimediaWidgets.so.5 points to libQt5MultimediaWidgets.so.5.9.2 in the same directory and the file is not there at all. So you need to either set the correct softlink path or have the file in same directory
First
Could it be that the pwd is not where you assume it is?
You could try adding
# Figure out where the application.sh script is located
scriptpath="$( cd "$(dirname "$0")" ; pwd -P )"
# Make sure our pwd is that location
cd "$scriptpath"
in the top of your script (assumes bash shell, from here)
By doing this all relative paths to Qt folder will be valid.
Second
Maybe you should considder exporting your new LD_LIBRARY_PATH, like so (from here):
LD_LIBRARY_PATH=whatever
export LD_LIBRARY_PATH
Third
It may be useful to run ldconfig command for ld to update after changing the variable (from here):
sudo ldconfig
The file libQt5MultimediaWidgets.so is not present in /Desktop/package/bin/Qt according to the screenshots shown.
Say I have to upload file dir-a/dir-b/dir-c/xxx.txt using sftp
Should I create the target directory first?
Should I open target directory before copying the file?
If have to create this path dir-a/dir-b/dir-c - is it one command or three?
Should I create the target directory first?
Usually yes. SFTP servers usually do not create parent directory. But how hard is it to try first?
Should I open target directory before copying the file?
You do not have to. put command does accept a remote-path, which can be either absolute or relative to remote working directory.
If have to create this path dir-a/dir-b/dir-c - is it one command or three?
These are three commands:
mkdir dir-a/
mkdir dir-a/dir-b/
mkdir dir-a/dir-b/dir-c
I have a general question as to why this occurs, and a misconception about 'pwd'.
You start with directory /test and in it you have /test/folder1.
Folder 1 has: file1.txt
In 2 separate terminals we "cd /test", and do an "ls" and discover folder1 as the output for both of these terminals.
We now "cd folder1" on terminal one. Terminal two remains in /test.
If we then "mv folder1 folder2" on terminal two and run an "ls" we get folder2 as the output. Clearly indicating our mv was successful.
However, within terminal 1 (which was in /test/folder1) if we run a "pwd" the output remains /test/folder1. Ie: it does NOT reflect that we have since moved the folder to /test/folder2.
Why is this the case? I can understand why if we were to edit the file1.txt it is just a pointer within the file system that should be pointing to the same file. Indeed it is as you can modify the file in each terminal and see the edits in the other. However, why is it the case that the 'pwd' command no longer reflects the actual path to that directory?
Thanks!
Assuming you're using bash, pwd is showing you the value of the PWD environment variable, which is updated when you change directory with cd. The folder1 directory changing name does not cause bash to update PWD. However you can find evidence that the directory has changed name:
pwd -P will show the new name of the directory.
ls -l /proc/self/cwd will link to the new name.
I think it is just the case that the first terminal has no reason to re-evaluate where it is. If you do the following command in the first terminal
cd .
you will see your current working directory has indeed changed per the rename (mv).
I want a create a file with a specific extension(.done). I am using the command touch. Something Like:
touch `basename $UNZIPFILE`".done"
It's creating the file but in current directory. I want to create this file in a specific directory. Is there a option to provide the directory ?
I checked : http://ss64.com/bash/touch.html , but could not figure out.
I can think of one option is before this command I can do a cd requiredDIR
Is there any other way, I can specify the Directory on the same command, so that I dont have to change the Directory?
Simply prepend the directory variable to the file you are touching.
touch "$MYDIR/$(basename $UNZIPFILE).done"
If the directory doesn't exist, you need to create it.
mkdir -p "$MYDIR" && touch "$MYDIR/$(basename $UNZIPFILE).done"
(It's also better to use $(command) syntax instead of backticks for command substitution.)