I have an Adafruit BLE Feather M0. I am following these instructions here - https://learn.adafruit.com/adafruit-feather-m0-express-designed-for-circuit-python-circuitpython?view=all
Really hoping someone can help me out as I am stuck in the very first task it self.
I see the board and select the correct one "Adafruit Feather M0" but the Port doesn't show serial options. It only shows the "/dev/cu.Bluetooth-incoming-Port" as an option. The instructions above show serial ports to choose from. What am I missing? This seems too basic to not work.
Looks like the cable I was using only supports charging and not data. TIL!
The other main thing, I think this is what hit me is that Arduino and Circuitpython are not enabled at the same time. If you install Cirtuitpython it will disable Arduino.
Related
I was troubleshooting why Serial1 was always throwing undefined errors in sketches I was trying to run when I found a solution posted online for a slightly different board that suggested this line:
HardwareSerial Serial1(2);
I uploaded it and now the Arduino doesn't show up in the IDE, did I remap it's serial communications? Why is this possible!
Is there any hardware factory reset option available on these boards? Did I just brick my device?
edit: It seems the STM32Cube programmer app can be used to communicate with the device but I'm not sure where to get the original firmware to flash. https://imgur.com/a/LbiHenf
Assuming from the tag in your question, I guess you have an STM32 – (BluePill) Development Board (STM32F103C8).
If you think that your board is not handling serial communication properly then you might consider burning bootloader to your board. This will reset the complete configuration of your board.
There are many ways in which you can burn bootloader to your board.
Using another Arduino board like Uno / Nano / Mega
Using an FTDI USB to TTL Serial Adapter.
You might want to go through tutorials list below:
Getting Started with STM32 using Arduino IDE: Blinking LED
Programming STM32F103C8 Board using USB Port
Okay, I've been working on this project for months with this being what has stopped me, heres the situation.
I am making a glove that can move a robot arm. The glove has an Arduino Nano iot 33 attached. The board measures the orientation with the built in imu, and sends it to my laptop (will be a raspberry pi in the future) through a usb cable. Also connected to the laptop is an Arduino Uno r3. This board is what makes the robot move (the servos are wired to it and I attached a display that shows the orientation of the glove here). I pondered how to make the Arduino Nano communicate to the Arduino Uno for a while, and I settled on keyboard presses. The Arduino Nano would press certain buttons based on its orientation and the Uno would wait for them to be pressed to move the robot. Turns out that after over 1000 lines of code, the Arduino uno can't use the keyboard library, and I'm stuck again. Is there a better way to go about this?? or is there a way to get the Arduino uno to get keyboard commands (I'm sixteen, tryin to save for college, I know theres a way to buy something to bypass the boards chip, I've already spent quite a bit on arduinos and PLA and such, and if im gonna buy something I want to use it again, please keep that in mind)
How would you have gone about this? How can I recover this project? Please help me...
this is an amazing project.
Great idea the link over SerialUSB, but it is very very slow...
You should use a radio transmitter like this.
Else, there is a great tutorial for communication using Bluetooth master & slave (warning: the post is in Italian).
If you still want to use SerialUSB, you should use a program that reads input from Nano and send a hex. code into Arduino Uno.
Library for serial communication with java or ruby.
Library for serial communication with Arduino.
I hope this can help you. Good luck!
I have an Arduino Uno and I am using arduino 1.0.5 IDE. I followed he procedures for bootloading an atmega328P-PU on a breadboard.
I uploaded the ArduinoISP sketch first, made the connections(using the External Oscillator) and then wired it up. Then, I selected the programmer as Arduino as ISP, selected the board as Arduino duemilanove w/ Atmega328P. Then I selected the correct serial port and clicked Burn Bootloader.
I got the following errors:
avrdude.exe: stk500_program_enable(): protocol error, expect=0x14,
resp=0x50avrdude.exe: initialization failed, rc=-1 Double
check connections and try again, or use -F to override
this check.avrdude.exe: stk500_disable(): protocol error, expect=0x14,
resp=0x51
How to solve this issue? Also, can I upload the bootloader directly by using it on the Uno in place of the original chip. If so, how?
to my understanding the error you have indicates a bad reading from the chip. I experienced that with chips that were either dead or not properly connected, especially to power supply.
You may find more detailed information in th tutorial : https://www.arduino.cc/en/Tutorial/ArduinoISP
Especially those things :
Note for Arduino 1.0: you need to make one small change to the
ArduinoISP code. Find the line in the heartbeat() function that says
"delay(40);" and change it to "delay(20);".
Select the items in the
Tools > Board and Serial Port menus that correspond to the board you
are using as the programmer (not the board being programmed).
Instead of arduino built-in boot loader just go through below link and it will be great for uploading boot loader and verifying board status info
I am replying you this because same issue I got long back and it saved me.
One more thing for arduino boot loader: for atmega328 you need to put capacitor between reset and gnd( in case you missed)
For gammon bootloader you don't need it.
Be Innovative.
For reset line you might me using 100nf(thats what stated in documentation )...but sometimes it doesn't work...try something like 4.7uf, 22uf or 47uf or close values
I had a similar problem and the issue was that my programmer was a bit slow, I used the -B flag for avrdude to slow down the bitrate and it started working, I set the -B20 and works like a charm every time, but I use the USBTinyISP programmer, not the stk500 one, so this might not work for you.
In case someone stuck at this as I did and nothing like changing the cap value helped. Make sure you are using your USB-TTL adapter in a 5v mode (obviously for a 5v powered chip). I always used it in a 3.3v mode in order not to accidentally burn my 3.3v chips and it always worked. Until today, I was trying to flash my custom atmega8 board and everything worked with the ISP but I was having a hard time using the bootloader and after half a day searching and trying different stuff the 5v setting to the rescue.
I am using arduino uno r3 board and arduino 1.6.5 on windows 8. When Itried to upload my program on ATMEGA328 microcontroller it is showing:
avrdude:stk500_getsync not in sync:resp=0x87.
help me to solve this error
This boils down to 3 problems usually..
The bootload on the chip is missing (unlikely if you purchased the board from Arduino).
The serial connection between the arduino and the computer is disconnected or interrupted.
You've simply selected the wrong board type or port when programming, and thus the IDE is searching for a signal that the arduino isn't coming back with.
This problem is most likely due to option 3, however it can occur in odd situations especially on the Arduino Micro where the board does all USB comms on chip and can be flooded by main without an appropriate delay to the point it can't communicate with the IDE. However this is just most likely a bad board selection or a bad port selection.
I've tried many things but this worked for me. If you have a working Arduino lying around (in my case Uno) you can use it as an intermediate in-system programmer (ISP).
Follow this guide to first load the ISP sketch into your working Arduino.
Once you are done, for your non-working Arduino, select from the Tools > Programmer menu and choose Arduino as ISP, and set Board and Processor accordingly. To program choose Sketch > Upload using programmer.
Hope this works.
I think the reason that this work is that it will bypass the CH340/FTDI chip, and all those synchronization issue. Given that that is your problem.
I recently completed this project with my Arduino (a fairly new hobby for me):
http://www.instructables.com/id/Make-a-24X6-LED-matrix/?ALLSTEPS
I can change the code to make whatever messages I want scroll accross the matrix but I thought it might be cool to have live information, like stock quotes, scroll accross. I think I could figure out how to do that except I would like to use it at work where there are lots of firewalls in place and I doubt Arduino software is on the approved list of programs. Is it possible to send messages to the Arduino through a USB without installing any drivers?
No it is impossible because data in Arduino is sent via serial command, the USB is only for convenience, but arduino work with FTD driver that emulate a serial connection. You should choose another type of connection bluetooth or wifi.
Hope this help you.