I recently completed this project with my Arduino (a fairly new hobby for me):
http://www.instructables.com/id/Make-a-24X6-LED-matrix/?ALLSTEPS
I can change the code to make whatever messages I want scroll accross the matrix but I thought it might be cool to have live information, like stock quotes, scroll accross. I think I could figure out how to do that except I would like to use it at work where there are lots of firewalls in place and I doubt Arduino software is on the approved list of programs. Is it possible to send messages to the Arduino through a USB without installing any drivers?
No it is impossible because data in Arduino is sent via serial command, the USB is only for convenience, but arduino work with FTD driver that emulate a serial connection. You should choose another type of connection bluetooth or wifi.
Hope this help you.
Related
I have been trying to set the limit of pairing the Bluetooth device HC-05(interface by Arduino controller) with my smartphone.
I have tried making this solution work with AT command
AT+INQM=<Param>,<Param2>,<Param3>
Example: AT+INQM=1,9,48\r\n
But instead of converting AT commands using serial.h with embedded C, I am looking for any dedicated library which helps to work this kind solution in using Arduino.
Basically, with the help of Bluetooth device connect to Arduino Nano, I want to send the altimeter sensor data to my smartphone.
During the connection, HC-05 should be responding any one device at a time, if another smartphone tries to pair then the error will be shown.
Please share your advice on this.
Yes there are some libraries in arduino but these are only meant for connection and pairing and low energy connections. We don't have any dedicated library from where we can control the mode of operation of HC05 or any bluetooth module. like bypassing or accessing GAP and GATT services of bluetooth. However there is a way to flash HC-05. But we can only use it for updating the firmware of this device. This github repo is dedicated for this purpose . Hope it helps you
Firstly, I'll just give you a brief introduction about our project... its "Speech controlled Home Automation System" where we are controlling the Home appliances by the voice or speech commands. We're successfully done with the voice recognition module. But our problem is with achieving the communication between the transmitter {where the user gives the voice command} and receiver {where the home appliances are present} through WiFi i.e. we have got 2 ESP8266 12E modules interfaced with Arduino both at the transmitter and receiver side and these two WiFi modules need to be communicated(To interchange some data sent by Arduinos).So please let us know which Arduino code need to be used at transmitter side wifi module and at Receiver side wifi module and also about the header files or additional softwares(if any)to be used.
you can achieve this by starting one of wifi modules in Access Point Mode and the other one has to be set to Station Mode in order to connect to the first one.
In case you want to add a router, just set both ESP8266 modules to Station Mode and connect them to the router.
And then transfer any data you want through AT commands of ESP8266.
Here is the refrence to them.
https://room-15.github.io/blog/2015/03/26/esp8266-at-command-reference/
If you are newbie to Esp8266 and Arduino , this will help you.
http://www.teomaragakis.com/hardware/electronics/how-to-connect-an-esp8266-to-an-arduino-uno/
Good Luck !
I worked on a similar system a year ago. I was developing a remote controlled toy. My main difference was I used the ESP8266 without an Arduino attached.
One ESP worked as a a WiFi hotspot and the other connected to it, sending messages through UDP.
For some reason, I could not get the two ESP modules to connect (I think it was a problem with the board I had), but I sent messages from my computer, and it worked out fine. I will not burden you with all of the code, but here is the GitHub link.
All that needs to happen is they will be on the same WiFi network, and then you can use the ESP8266 WiFi library to send messages between the two. Like I said above, I used UDP, which is good for high speed, with no error checking. But there is also TCP (higher up, has error checking code), or you can use the server/client part of the library to set up a full web server and read/write data to it. Without knowing what type of data, I cannot comment on what would be the best method.
As for headers, you will need WiFi.h, and if you are using UDP you will need WiFiUdp.h
You should not need any external software besides the Arduino IDE.
I taught myself from scratch for this product, using two main resources: the Arduino library reference, and the docs on the ESP8266 Arduino GitHub page
Hello I am trying to get my ESP to run a webserver that will accept a string of text an output that text through a the uart serial pins to my arduino I can't find out how to do it I would apreshiate it
My seyup would be
Arduino connected to the esp through serial pins the esp would start a server and my pc would open the webserver and type in a string of text that string would transmit to the arduino
I can't comment yet, so I'll put this in an answer :)
What I understand is you want a simple 'webserver' on your ESP, that listens to simple GET requests, takes the query string, and sends that over the serial line to your Arduino.
Firstly, are you capable of flashing new firmware to the ESP?
It's not hard, but as I understand your request, you will need to be able to do it.
Then you need to pick what would be your preferred approach:
Flash NodeMcu firmware, and expand the webserver lua example to do what you want.
Set up the Arduino IDE to work with the ESP (tutorials exist), and write a Arduino sketch to do what you want.
You could also use esp-open-sdk, or the official Espressif SDK, and write what you want in C, but since you sound like a beginner, the two previous options are likley a better choice, their easier.
I expect the NodeMcu/lua way might be the quickest, although if you're already familiar with the Arduino IDE that might be a better choice.
If there are details you are stuck on, expand your question, and I'll see if I can stick them in the answer.
I am using 2 esp8266 wireless modules to establish bidirectional wireless communication between 2 arduino boards (one mega and one uno) without the use of any earth based technologies (i.e. radio frequencies, wifi which relies on earth sattelites, etc.). My solution was to use the esp8266 to establish a private area network with both esp's acting as a station and an access point (AT+CIPMODE=3). Unfortunately, this solution has proven to be more of a hassle than it was worth.
To start, I have the esp's each wired according to this diagram
When I first started out, the red LED was on and the blue LED was off. During this time, I was able to send AT commands, establish the server, and achieve the communication I required by entering commands directly to the serial monitor. After this, I started writing a library using the SoftwareSerial library to allow me to issue commands directly through the program to set up the esp as needed upon start up of my script. Before doing this, I changed the baudrate to make sure it was running at 9600, and entered the AT commands in the serial monitor to make sure everything was working properly and it still worked.
After I began writing the library, before uploading the code with a test of the library I noticed the blue LED was lit solid now. Noticing this, I reuploaded the barebones script (I haven't uploaded the library code to the arduino yet) and the esp was no longer receiving the AT commands.
Does this indicate an issue with the board which I can fix or does this mean the board is done?
With my deadlines approaching fast in about 3 weeks it is crucial I get this wireless communication working so if this is an issue with the board, I'm going to have to scrap the esp's and use a different way of communicating. So my second question is, if this is the case, what are other viable options for establishing this communication? I have used xbee's before and while that would be ideal, they fall out of the budget I have been alotted so I need to keep it under $50 for this. If bidirectional communication is not possible for that price I can live with one way because I just need to get this system working. Basically I just need to transmit a single byte of data.
I realize this response is a little belated, and I hope you got it sorted: I've started working with the ESP8266 myself in the last few weeks, and hence why I was looking around for tutorials on direct communication between 2 units, when I found your post.
From what I've been able to ascertain, the AT commands are a part of the 'firmware' which ships with some modules. The Arduino code however starts loading onto the chips at memory address 0x0000, which is the same address that the firmware update tools use.
In other words, I believe that with the Arduino-coded program running on there, you lose the AT command functionality.
If you find a firmware update tool for the ESP8266 (plenty online) you'll get back the AT commands.
I suppose though the real question is why would you want to? It seems that the AT commands are just a way to treat the ESP as a dumb WiFi antenna. With the Arduino code, you're actually treating it as a micro-controller in its own right.
How can I send a string via serial communications from Java or Python? I have a very little arduino program that will recieve a CSV string of ints that each control different relays (I adapted it from their example).
I just got an Arduino, and I am trying to use it to open and close a relay remotely. I have it opening and closing the relay, no problem. But I really have no idea where to start as far as using serial communication.
I have a bluetooth dongle that I can connect to, but once I do that I'm lost.
Also, this is my first time using serial communications AND my first time using an Arduino. So I'm sorry if I am completely off on some of the things I am asking. All I know is what I've learned from Google.
Thank you very much
You can use any Java or Python serial port classes and methods. There is however one thing you need to be aware of.
The newer arduino's have a feature known as AutoReset. This works by connecting the DTR signal from the serial port to the Reset line on the chip using a capacitor or such. The IDE uses this to reset the board to activate the bootloader and initiate uploading code to the arduino. The serial monitor in the IDE is aware of this and does not toggle the DTR line when comunicating with the device (except when it initially connects).
There is are several ways to defeat this feature and you can read about them here.
As for actually comunicating with the device, there are several tutorials about serial communication in both Java and Python.
Pyserial includes the option to not use the DTR lines when opening a port.
Here is a website explaining how to use RXTX (a Java library) to comunicate with an Arduino
Best of luck.