I've a tape contains a corrupt tar file.
I'm using Unix SunOS 5.5.1.
So when I run this command :
dd if=/dev/rmt/0 of=/tmp/outputfile.tar
I get this error message :
warning /pci#1f, 0/pci#1/pci#1/sunw, isptwo#4/st#4,0 (st4):
Error for command : read Error Level: Fatal
Requested Block : 11900 Error Block : 11900
Vendor : TANDBERG Serial Number: =:CREATED081
Sense Key: Media Error
ASC: 0x11 (unrecorded read error), ASCQ: 0x1, FRU: 0x0
Please Help me I really need solution for this problem
Finally I solved my problem ^^' it was the bs format type :D
Data was written in 512 so I did this :
dd if=/dev/rmt/0 of=/tmp/outputfile.tar bs=512 and all is fine :)))
The bad news is that the tape drive is reporting a media error.
Now this still can mean a few things:
Bad tape drive
This is possible, but rather uncommon. To test it: check if it can read other tapes (it wrote itself), or read tapes other drives wrote.
Dirty heads
Tape drives heads do need periodic cleaning. Esp if they are kept in less that spotless conditions this is very important. Cleaning tapes are commercially available, do match them with the right drive and do not overuse them either.
Mismatch between tape drive and tape medium
Different tape formats (e.g. LTO) have generations (e.g. LTO-3), and there is a need for compatibility between the tape medium and the tape drive.
Bad tape
Tapes do wear out, and need replacement to prevent that. Moreover a written tape has a limited shelf life just as well.
In this last case, you might be able to find a commercial recovery service to try to do something, but I'd not bet the farm on the results ... And data recovery services are expensive ...
Closed. This question is not reproducible or was caused by typos. It is not currently accepting answers.
This question was caused by a typo or a problem that can no longer be reproduced. While similar questions may be on-topic here, this one was resolved in a way less likely to help future readers.
Closed 4 years ago.
Improve this question
I want to comment out a block of multiple lines in Jupyter Notebook, but can't find out how to do that in this current version.
It used to be in one of the drop down menus but is no longer there.
How do you comment out multi-line blocks of code at once?
This is not a duplicate because the solution given in the following link doesn't seem to work anymore:
How can I block comment code in the IPython notebook?
Ctrl + / does nothing.
Ctrl + / works for me in Chrome browser in MS Windows. On a Mac, use Cmd + / (thanks Anton K).
Please note, if / did not work out of the box, try pressing the / key on the Numpad. Credit: #DreamFlasher in comments to this question.
I have not yet managed to find the best way possible. Since I am using a keyboard with Finnish layout, some of the answers do not work for me (e.g. user5036413's answer).
However, in the meantime, I have come up with a solution that at least helps me not to comment each and every line one by one. I am using Chrome browser in MS Windows and I have not checked other possibilities though.
The solution:
It uses the fact that you can have multiple line cursors in an Ipython Notebook.
Press the Alt button and keep holding it. The cursor should change its shape into a big plus sign. The next step is, using your mouse, to point to the beginning of the first line you want to comment and while holding the Alt button pull down your mouse until the last line you want to comment. Finally, you can release the Alt button and then use the # character to comment. Voila! You have now commented multiple lines.
Try using the / from the numeric keyboard.
Ctrl + / in Chrome wasn't working for me, but when I used the /(division symbol) from the numeric it worked.
Quick Addition to Top Answer: CTRL + / is nice because it toggles back and forth between adding and removing # at beginning of all selected lines. Didn't see that exact nuance mentioned so just wanted to add it here. (This worked in Firefox Developer Edition 54.0b12 on Windows 7).
On a Finnish keyboard use Ctrl + ' to comment on multiple lines and use the same keys to de-comment.
Ubuntu 14.04 Google Chrome
TL;DR:
Using MacBook Pro with Spanish - ISO Keyboard.
Solution: Ctrl + -
Full story
This is an old post but reading it got me thinking about possible shortcuts.
My keyboard is a Latin Apple MacBook Pro, which is called Spanish - ISO. I tried the changing keyboard distribution to U.S. solution... this works but with this solution I have to switch keyboards every time I want to comment which... sucks.
So I tried ctrl + - and it works. The - is where the / is located in an english keyboard but doing Cmd + - only changes the Chrome's zoom so I tried Ctrl which isn't as used as Cmd in macOS.
My takeaway with this would be: if I have more shortcut problems I might try the original shortcut but using the key where the U.S. keyboard would have it.
Select the lines you want to comment out. Then press:
Ctrl + #
I tried this on Mac OSX with Chrome 42.0.2311.90 (64-bit) and this works by using CMD + /
The version of the notebook server is 3.1.0-cbccb68 and is running on:
Python 2.7.9 |Anaconda 2.1.0 (x86_64)| (default, Dec 15 2014, 10:37:34)
[GCC 4.2.1 (Apple Inc. build 5577)]
Could it be a browser related problem? Did you try Firefox or IE?
Use triple single quotes ''' at the beginning and end. It will be ignored as a doc string within the function.
'''
This is how you would
write multiple lines of code
in Jupyter notebooks.
'''
I can't figure out how to print that in multiple lines but you can add a line anywhere in between those quotes and your code will be fine.
Fn + Cmd + / in Safari browser on MacOS
On MacOS 10.11 with Firefox and a German keyboard layout it is Ctrl + ?
Select the lines on windows jupyter notebook and then hit Ctrl+#.
I add the same situation and went in a couple of stackoverfow, github and tutorials showing complex solutions. Nothing simple though! Some with "Hold the alt key and move the mouse while the cursor shows a cross" which is not for laptop users (at least for me), some others with configuration files...
I found it after a good sleep night. My environment is laptop, ubuntu and Jupyter/Ipython 5.1.0 :
Just select/highlight one line, a block or something, and then "Ctrl"+"/" and it's magic :)
After searching for a while I have found a solution to comment on an AZERTY mac. The shortcut is Ctrl +/= key
I am using chrome, Linux Mint; and for commenting and dis-commenting bundle of lines:
Ctrl + /
For a Dutch keyboard layout (on Debian 9 in Chromium 57) it is Ctrl + °
Another thing to add, in the version I'm using, the code has to be initialized in order to be to comment it out using CTRL and / . If you haven't ran the code and the code isn't colorized it wont work.
If you have a Mac and not a English keyboard:
Cmd-/ is still easy to produce.
Follow the below steps:
Just go into the Mac's System Settings, Keyboard, tab "Input Sources" or whatever it might be called in English
Add the one for English (shows up as ABC, strange way to spell English).
Whenever you want a Cmd-/, you have to change to the ABC keyboard (in your menu row at the top of your screen,if you have ticked it to be shown there in the System Settings - Keyboard tab).
Cmd and the key to the left of the right "shift key" gives you Cmd-/.
P.S: Don't forget to switch back to your normal keyboard.
Do you guys know, if there is any way, to interrupt a winProgressBar?
I tried to press Escape, but it would not stop the progress bar during calculations.
Thanks for any help
W
You can press Alt + F4 , just like you would close any program in Windows.
I've got two error messages:
cv::mat::deallocate
cv::fastFree(void *)
While I was trying to compile my OpenCV and QT project. I am fighting with this problem for fifth day. Please guys if you know how I can solve this problem, write it here.
PS: I've uploaded an image.
http://postimg.org/image/wsyq8daf5/
After this day, my problem with the camera was totally solved.There are no more problems.Now i will continue my GUI project thanks to all of you guys.After 1-2 months i will start searching for how to write printer driver ;), but however.Thanks too all again. ;)
Finally i solved my problem using the QCamera class.Well guys, use QCamera, you don't need anything else to capture videos or images.Read everything about it and bye bye ;)
I noticed this question has been asked many times in the past and surfing the web I found many pages about it. However, it seems like the proposed solutions rarely work and, in my case, the problem does not refer to a program that I wrote. So I'll give it another try here.
I recently installed Linux Mint 14 on my laptop. After the OS was spick and span, I started to install the software I need, and among these netgen (a Mesh Generator software). I tried both ways: download+unpack+compile+install and synaptic. Either way, this is the output I get when I try to execute the program
X Error of failed request: BadAlloc (insufficient resources for operation)
Major opcode of failed request: 154 (GLX)
Minor opcode of failed request: 3 (X_GLXCreateContext)
Serial number of failed request: 490
Current serial number in output stream: 491
As I said, I surfed the web, and apparently, this is thought to be linked to some problem in the X server configuration. And here start the mess. Someone says I should modify /etc/X11/Xorg.conf, adding the lines
Option "Videoram" "65536"
Option "Cachelines" "1980"
Under the section "Device." Unfortunately, I have no such file, as apparently in recent distros, the X configuration file has been moved to /usr/share/X11/xorg.conf.d/* and it's now split into different files. The one about the monitor and graphics should be called 10-monitor.conf...which I don't have. I tried to create one, following the instruction at this link, and then add those lines, but nothing happened. To be fair, I'm not 100% sure I generated the file correctly since I am not sure how to detect the driver for my graphics card.
I don't know how much and which information people would need to have an idea of how to fix this problem. Here's what I see might be useful.
The output of 'lspci | grep VGA' is
01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee
ATI RS880M [Mobility Radeon HD 4200 Series]
My current /usr/share/X11/xorg.conf.d/10-monitor.conf is the following
Section "Monitor"
Identifier "Monitor0"
Modeline "1920x1080_60.00" 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -HSync +Vsync
EndSection
Section "Device"
Identifier "LVSD"
Driver "fglrx" #Choose the driver used for this monitor
EndSection
Section "Screen"
Identifier "Screen0"
Device "LVDS"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1920x1080_60.00" "1366x768"
EndSubSection
EndSection
Under the section "Device." Unfortunately, I have no such file
Try creating your own xorg.conf file, placing it in this location will override your X settings after restarting X or simply by restarting the computer.
mkdir -p /etc/X11/xorg.conf.d/
cp /etc/X11/xorg.conf.d/xorg.conf /etc/X11/xorg.conf.d/xorg.conf.bk # in case it exists
cp /usr/share/X11/xorg.conf.d/10-monitor.conf /etc/X11/xorg.conf.d/xorg.conf
The content of /etc/X11/xorg.conf.d/xorg.conf would look like (adding your options):
Section "Monitor"
Identifier "Monitor0"
Modeline "1920x1080_60.00" 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -HSync +Vsync
EndSection
Section "Device"
Identifier "LVSD"
Driver "fglrx" #Choose the driver used for this monitor
Option "Videoram" "65536"
Option "Cachelines" "1980"
EndSection
Section "Screen"
Identifier "Screen0"
Device "LVDS"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1920x1080_60.00" "1366x768"
EndSubSection
EndSection
This also could be related to the driver you're using, there are other common drivers available like
Driver "fbdev"
Driver "vesa"
Driver "fglrx"
The fbdev driver supports all hardware where a framebuffer driver is available.
The vesa driver supports most VESA-compatible video cards. There are some known exceptions, and those should be listed here.
fglrx is a X.org(7x) driver for ATI (Mobility(TM)) RADEON® and (Mobility(TM)) FireGL(TM) based video cards. The driver provides hardware acceleration for 3D graphics and video playback. It includes support for dual displays, TV Output and as of version 8.21.7 also OpenGL 2.0 (GLSL).
Depending on which driver you choose, certain options/functionality/compatibility would be enabled or not, you could change the driver and test with the options you said would work.
Finally, you have hundreds of options here to play with X11.
When I had made written a lot text to my program I took similiar error. When I reduce the text size the error was disappeared. I think you should reduce too showing things or reorganise how they are looking on screen.
I hope I could help you with this broken English ;)