I recently migrated a site to a new server and am now trying to replace the old domain by the new one using this tool suggested in the wordpress codex.
The SQL instance and the VM are both in the same region and are connected using a cloud sql proxy, however when I try and connect to the database via the searc-replace tool, I get connection refused:
EDIT:
The command used to start the sql proxy is the following:
localhost:/cloudsql/project-name:region:sql-instance-name
It is the same I use in the config file to connect the site to the db.
"Connection Refused" error occurs when an application attempts a TCP connection but there is either no service listening on the target address and port or a firewall rejecting the connection.
First, lets make sure you are connecting on the right port. Run sudo netstat -lntp and look for cloud_sql_proxy. For example you might see
tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN 71313/cloud_sql_pro
indicating cloud sql is listening on port 3306. If you saw this, you should change the port in your tool to 3306.
If netstat does not show any cloud_sql_proxy line, then it isn't listening on TCP. While TCP isn't always needed for MySQL, it looks like the tool your are using does need it. Make sure you start cloud_sql_proxy with -instances=<INSTANCE_CONNECTION_NAME>=tcp:3306
Second, lets make sure you are connecting on the right address. This should be localhost without :/cloudsql/project-name:region:sql-instance-name after.
If it still doesn't work after those two, use sudo iptables -L to look for firewall rules blocking the traffic. I believe it's unlikely that you have a firewall stopping local traffic, however.
An alternative to using the Cloud SQL Proxy is to connect directly to your instance. To do this:
Find the external IP address of the VM you are running the PHP tool on.
Grant access for that IP address to your SQL instance, with the instructions here
Because MySQL can have different username/password depending on where you connect from, ensure there is a username/password combo for host %. instructions here.
Use the tool, with the username/password from (3), port=3306 and host=the IP address of your SQL instance
When you are done, remove access from the IP address to your Cloud SQL instance.
I'm trying to use NETSH PORTPROXY command to forward packets sent to my XP PC (IP 192.168.0.10) on port 8001 to port 80 (I've a XAMPP Apache server listening to port 80).
I issued the following:
netsh interface portproxy add v4tov4 listenport=8001 listenaddress=192.168.0.10 connectport=80 connectaddress=192.168.0.10
Show all confirms that everything is configured correctly:
netsh interface portproxy show all
Listen on IPv4: Connect to IPv4:
Address Port Address Port
--------------- ---------- --------------- ----------
192.168.0.10 8001 192.168.0.10 80
However, I'm not able to access apache website from http://localhost:8001. I'm able to access through the direct port at http://localhost as shown below.
Additionally, I've also tried the following:
1. Access the Apache website from a remote PC using the link: http://192.168.0.10:8001. Firewall turned off.
2. Changing listenaddress and connectaddress to 127.0.0.1.
Without further information, I can't find a way to resolve the problem. Is there a way to debug NETSH PORTPROXY?
Note: By the way, if you're wondering why I am doing this, I actually want to map remote MySQL client connections from a custom port to the default MySQL Server port 3306.
I managed to get it to work by issuing:
netsh interface ipv6 install
Also, for my purpose, it is not required to set listenaddress and better to set connectaddress=127.0.0.1, e.g.
netsh interface portproxy add v4tov4 listenport=8001 connectport=80 connectaddress=127.0.0.1
If netsh's port proxying is not working as expected, then you should verify the followings, preferably in that order:
Make sure the port proxy is properly configured
Start or restart the related Windows service
Ensure support for IPv6 is installed
Make sure the port is not blocked by a firewall
Make sure the port proxy is properly configured
This might seems to be trivial, but just in case, take the time to review your configuration before you go any further.
From either a command prompt or PowerShell prompt, run the following command:
netsh interface portproxy show all
The result should look something like this:
Listen on ipv4: Connect to ipv4:
Address Port Address Port
--------------- ---------- --------------- ----------
24.12.12.24 3306 192.168.0.100 3306
24.12.12.24 8080 192.168.0.100 80
Carefully review those settings. Make sure that you can indeed connect to the addresses on the right side of that list, from the local computer. For example, can you locally open a web browser and reach 192.168.0.100:80? If the protocol is not HTTP, then use telnet: telnet 192.168.0.100 3306 (see here for how to install the Telnet client on Windows).
Then, are the values on the left side correct? Is the IP address valid for your machine? Is that the port number you are trying to connect to, from the external machine?
Start or restart the related Windows service
On latest versions of Windows, netsh's port proxying is handled by a Windows service named "IP Helper" or "iphlpsvc". Proxying will obviously not work if that service is stopped. I have also faced situations that turned out to be resolved by restarting that service.
To do that in latest versions of Windows:
Open the Task manager, then go to the Services tab.
In the "Name" column, find the service named either "iphlpsvc" or "IP Helper".
Right click on that service, then select Restart. If restart is not available, then the service is probably stopped, and actually has to be started, so select Start.
On previous versions of Windows, look for Services in Administrative Tools, inside the Control Panel.
Ensure support for IPv6 is installed (older releases of Windows only)
On earlier versions of Windows (that is Windows XP, for sure, upto some early releases of Windows 10, apparently, though this is not clear), netsh's port proxying feature (including for IPv4-to-IPv4 proxys) was actually handled by a DLL (IPV6MON.DLL) that was only loaded if IPV6 protocol support was enabled. Therefore, on these versions, support for the IPv6 protocol is required in order to enable netsh's port proxying (see Microsoft's support article here).
From either a command prompt or PowerShell prompt, run the following command:
netsh interface ipv6 install
If you get an error indicating that command interface ipv6 install was not found, then it means that you are using a recent release of Windows, in which netsh's IPv6 support is implicit and cannot be disabled.
Make sure the port is not blocked by a firewall
A local firewall may potentially block the port even before they reach the IP Helper service. To make validate this hypothesis, temporarily disable any local firewall (including Windows' native firewall), then retest. If that works, then simply add a port exclusion to your firewall configuration.
I have the problem with you. I have solve it just now. There is a Windows Service named "IP Helper" that supplies the funcions tunnel connections. You should ensure it has been started.
You must Run Command.exe as Administrator first, by right-clicking the Command Prompt icon and choosing Run as Administrator. You will asked to confirm.
Paste your netsh Command in the command.exe window and press Enter.
If no error message is shown, the command worked.
In your web browser go to http://your-up:8001 to see it works.
The Windows Event Log might have information to help find the cause of a failure.
When I start couchDB I have it running on http://127.0.0.1:5984/. I have another program I need to run on the same port, so I want to change the couchDB one to something else. Any ideas?
Specify the port in your local.ini config:
[httpd]
port = 5984
Hi I have a server running on my computer, and the client program tries to connect with my IP address on port 5000 through a TCP connection. How do I get my computer to allow this? I know it has something to do with port forwarding settings but I forget how to do it. I use Verizon if that helps.
It depends on your location / computer / OS which you don't specify. It sounds though like your running a server at home??
To accomplish this in Windows, I would set a rule on my router to allow tcp over 5000 and specify to which local IP address to forward it and on the receiving PC/server in Windows Firewall set a custom rule to again allow tcp 5000.
I'm trying to connect from my ms windows 7 via the odbc administrator to a remote
sybase sqlanywhere 11 database server.
But I get not connection, I'm not sure which configure option I have to specify.
server-name = ip address of remote database server?
startline ?
portnummer ?
Thank you, best regards, Alex
By default the SQL Anywhere server process dbsrv#.exe listens for incoming connections on port 2638.
Make sure your firewall allows outbound connections to that port.
Assuming you have a database running on your server as follows:
-x tcpip
-n my_server_name
"[DIR]\database_main_file.db" -n my_database_name
The server will broadcast on the tcp/ip layer on the default port (2638) under the name "my_server_name" and the database will be accessible under the name "my_database_name" via ODBC
Creating an ODBC entry for your new database to connect from a client (adjust for Windows 7)
[HKEY_LOCAL_MACHINE\SOFTWARE\ODBC\ODBC.INI\myodbcentry]
"Driver"="C:\\PROGRA~1\\SQLANY~1\\Bin32\\dbodbc11.dll"
"DatabaseName"="my_database_name"
"ServerName"="my_server_name"
"LINKS"="TCPIP(IP=SERVER_IP_ADDRESS;PORT=2638)"
There are other parameters available for LINKS (HOST, etc). Take a look at http://dcx.sybase.com/index.html#1101en/dbadmin_en11/da-using-tcpip.html
I've seen some rare issues with UDP broadcast packets. See the docs at
http://dcx.sybase.com/1101en/dbadmin_en11/broadcastlistener-connection-conparm.html and check with your network administrator.
You can also use the dbping.exe utility to troubleshoot networking issues.
BTW, you may want to cross-post your question at http://sqla.stackexchange.com. It's full of SQL Anywhere buffs