I just bough NUC120, and there is nothing less than expected. What sparked my interest is, as stated on page 17-18 on the datasheet, It able to do UART communication. So far, I only use the USB port to uploading the firmware via ISP using NuMicro ISP Programming Tools. I've noticed (correct me if I'm wrong) that its the same concept with Arduino boards, where the USB port can be used to both programming and communication. I have do my research for several days, but still can't find how to do serial communication between Nuvoton and PC, since when I do programming using NuMicro, I use "USB" connection type, and on my PC, there is no COM PORT listed.
My question, Is it possible to do serial communication via Nuvoton USB port? If its possible, can you please point me where to look?
Thanks in advance. Please tell if I should add more details about this question.
You can find the examples in the BSP documentation. Look for samples of USBD_VCOM. To be able to communicate with your PC, you have to install the driver of Virtual COM manually
Related
I have a raspberry pi 4 and a pc, I have to transfer files at very high speed than Ethernet and WIFI
if any possible methods are there Please tell me?
I'm not too sure if you're saying you want to transfer files over something other than wifi or Ethernet? If so, USB A to USB A should work for you. PCIe are downstream slots which you would be unable to connect to another system using that method. If you are able to plug up to each of the systems using ethernet, that's probably your easiest choice. As long as you bridge the connections and allow file printing and sharing, you should be able to see the system in your file explorer.
My work involves interacting with legacy hardware that uses serial ports. I often have to monitor more than one serial line, and for the purpose I have a couple of the common USB serial adaptors. When I connect both of them to the same (Windows 10) machine, irregularities show up. Both ports show up in device manager, but only the first one that I plug in to the USB connector works. The other one indicates port not open when I try to send data via RealTerm.
I have also seen the situation where when I plug the second adaptor in, its port comes up, but the one for the other adaptor disappears. Does anyone know a way that two devices can happily coexist on the one machine? Thanks in advance.
Just ion case this helps anyone in the future......
The problem seems to be caused by the fact that one of the adaptors was coming in via a (powered) USB hub. When I liberated another native port on the machine so I could host both serial adaptors directly, everything worked fine.
Not worth hunting the cause down, a solution is at hand.
I have gone through several links online but I have not found any appropriate solution to it. I am wondering if there is a way to connect an Arduino with WiFi without using any shield or any other external hardware. My laptop is connected to WiFi and the arduino board is connected to the laptop with an USB cable. I want to access/run the data for the Arduino using WiFi. Is there a way to do it?
Hope my query makes a sense.
Thanks.
Let's restate your question for clarity - you want to share the laptop's Internet connection (e.g. via WiFi) with the Arduino connected to the laptop with a USB cable, with no additional hardware?
Assuming I restated it correctly, the Arduino's USB connection provides a virtual "serial port" for communication. This means you can use an "IP over serial" solution for Internet access. One such common and widely supported solution is PPP.
However, programing the Arduino with IP over PPP stack requires significant amount of memory and is probably an overkill for whatever it is you're trying to do.
You're probably better off designing a custom-tailored protocol for the serial communication between the Arduino and a small gateway program you can program and run on the laptop.
If you're bent on a complex solution that provides full Internet access to the Arduino, the steps to achieve what you're after are:
Program the Arduino with a TCP/IP over PPP protocol stack, running on the serial port. You'll probably need an Arduino MEGA.
Setup the laptop to be a PPP endpoint on the Arduino's serial port. For a Windows machine you can refer to this page for information on how to do that.
Once the PPP link is up, you can setup the laptop's OS to share Internet access to the PPP link.
I'd like to connect a beagleboard-like (custom developed) omap board to a Windows PC using a virtual-com setup. That is, i'd like the board to appear to Windows as a com device and get the COM to send data to our application on the board. The main reason for that is to use virtual-com drivers on windows, since the usb drivers we use now to directly sent data over usb between the host and the board seem not to work properly.
I have done this using the FTDI driver on the past but as far as i know it worked because the device had an FTDI chip that translated the usb protocol to serial signals (am i right ?).If there's no USB to UART bridge on the board, how could i do that ?
By the way, how USB Communication Device Classes fits here ? Should develop a CDC driver for the board ? What should I use then on Windows side ?
I'm kind of confused, so any help will be greatly appreciated :)
Well, i answer myself :)
The solution lies in the Linux USB Gadget Subsystem.
Gadget API
What I have in mind is having a number of sensors (temperature, accelerometer, sound level meter) that are controlled by a micro controller. What I want to do is take this information and transmit it wireless to a laptop that will take this information and put it on to a web server using Zigbee. I don't know where to start.
Since you don't have any hardware as of yet, you might want to give the Arduino a try. The hardware is affordable, can be connected to your system via USB while being programmable in-system.
The basic board can be extended via so called "shields", which offer additional features. In your case, the XBee shield would be appropriate. Connecting your laptop to a XBee module is as simple as using Sparkfun's breakout board and a mini-USB cable.
The Arduino has a large community, so you will find a lot of resources, like books, online material, example code etc.
We also provide wireless modules that can be used for serial data transmission. They can be found at www.starmanelectric.com Our modules are very similar to the xbee, but more plug and play. They can be a great for going wireless for the first time. Our devices are designed to function like a "wireless cable" so if you're used to using wires then you'll be up and running in no time at all. We also have circuit examples for transmitting to a laptop serial port or USB. Any micro-controller will be fine for this application, as long as it has a serial port and a few ADCs to sample your data. Our modules also provide simple analog in/out which can run in parallel to the serial. If you want to compare to other systems, I would google "wireless serial modules"
Regards,
Michael
Starman Electric