I am using 2 esp8266 wireless modules to establish bidirectional wireless communication between 2 arduino boards (one mega and one uno) without the use of any earth based technologies (i.e. radio frequencies, wifi which relies on earth sattelites, etc.). My solution was to use the esp8266 to establish a private area network with both esp's acting as a station and an access point (AT+CIPMODE=3). Unfortunately, this solution has proven to be more of a hassle than it was worth.
To start, I have the esp's each wired according to this diagram
When I first started out, the red LED was on and the blue LED was off. During this time, I was able to send AT commands, establish the server, and achieve the communication I required by entering commands directly to the serial monitor. After this, I started writing a library using the SoftwareSerial library to allow me to issue commands directly through the program to set up the esp as needed upon start up of my script. Before doing this, I changed the baudrate to make sure it was running at 9600, and entered the AT commands in the serial monitor to make sure everything was working properly and it still worked.
After I began writing the library, before uploading the code with a test of the library I noticed the blue LED was lit solid now. Noticing this, I reuploaded the barebones script (I haven't uploaded the library code to the arduino yet) and the esp was no longer receiving the AT commands.
Does this indicate an issue with the board which I can fix or does this mean the board is done?
With my deadlines approaching fast in about 3 weeks it is crucial I get this wireless communication working so if this is an issue with the board, I'm going to have to scrap the esp's and use a different way of communicating. So my second question is, if this is the case, what are other viable options for establishing this communication? I have used xbee's before and while that would be ideal, they fall out of the budget I have been alotted so I need to keep it under $50 for this. If bidirectional communication is not possible for that price I can live with one way because I just need to get this system working. Basically I just need to transmit a single byte of data.
I realize this response is a little belated, and I hope you got it sorted: I've started working with the ESP8266 myself in the last few weeks, and hence why I was looking around for tutorials on direct communication between 2 units, when I found your post.
From what I've been able to ascertain, the AT commands are a part of the 'firmware' which ships with some modules. The Arduino code however starts loading onto the chips at memory address 0x0000, which is the same address that the firmware update tools use.
In other words, I believe that with the Arduino-coded program running on there, you lose the AT command functionality.
If you find a firmware update tool for the ESP8266 (plenty online) you'll get back the AT commands.
I suppose though the real question is why would you want to? It seems that the AT commands are just a way to treat the ESP as a dumb WiFi antenna. With the Arduino code, you're actually treating it as a micro-controller in its own right.
Related
Firstly, I'll just give you a brief introduction about our project... its "Speech controlled Home Automation System" where we are controlling the Home appliances by the voice or speech commands. We're successfully done with the voice recognition module. But our problem is with achieving the communication between the transmitter {where the user gives the voice command} and receiver {where the home appliances are present} through WiFi i.e. we have got 2 ESP8266 12E modules interfaced with Arduino both at the transmitter and receiver side and these two WiFi modules need to be communicated(To interchange some data sent by Arduinos).So please let us know which Arduino code need to be used at transmitter side wifi module and at Receiver side wifi module and also about the header files or additional softwares(if any)to be used.
you can achieve this by starting one of wifi modules in Access Point Mode and the other one has to be set to Station Mode in order to connect to the first one.
In case you want to add a router, just set both ESP8266 modules to Station Mode and connect them to the router.
And then transfer any data you want through AT commands of ESP8266.
Here is the refrence to them.
https://room-15.github.io/blog/2015/03/26/esp8266-at-command-reference/
If you are newbie to Esp8266 and Arduino , this will help you.
http://www.teomaragakis.com/hardware/electronics/how-to-connect-an-esp8266-to-an-arduino-uno/
Good Luck !
I worked on a similar system a year ago. I was developing a remote controlled toy. My main difference was I used the ESP8266 without an Arduino attached.
One ESP worked as a a WiFi hotspot and the other connected to it, sending messages through UDP.
For some reason, I could not get the two ESP modules to connect (I think it was a problem with the board I had), but I sent messages from my computer, and it worked out fine. I will not burden you with all of the code, but here is the GitHub link.
All that needs to happen is they will be on the same WiFi network, and then you can use the ESP8266 WiFi library to send messages between the two. Like I said above, I used UDP, which is good for high speed, with no error checking. But there is also TCP (higher up, has error checking code), or you can use the server/client part of the library to set up a full web server and read/write data to it. Without knowing what type of data, I cannot comment on what would be the best method.
As for headers, you will need WiFi.h, and if you are using UDP you will need WiFiUdp.h
You should not need any external software besides the Arduino IDE.
I taught myself from scratch for this product, using two main resources: the Arduino library reference, and the docs on the ESP8266 Arduino GitHub page
I've been trying to establish serial (UART) communication between a Raspberry Pi Model B Revision 2.0 (checked the model like described on this page) and Arduino Mega 2560. I made a service on the Pi that writes to UART and then expects a message and a coworker programmed the Arduino with an echo program. While they were communicating, I had trouble receiving data, meaning that it was clustered in 8 byte pieces and I had to introduce a timeout for waiting between them (I was actually as much as available and calling select()for the next cluster but it turned to be 8bytes a cluster, except for maybe the last one. As explained in a question I found on this site, the programmer is the one to take care of the protocol and can not rely that the whole message will be ready to read at once (that is logical).
However, when I just connected Pi's TXD and RXD pins, no matter how much bytes I tried sending, it sends them in one go (I've gone up to a bit more than 256, that's more than enough for my purposes). I also have around 50 milliseconds of duration difference, measured directly from within the program, using gettimeofday() function.
So, could anybody clear things for me:
Why is this happening?
Is this difference in behaviour expected?
Is there a potential problem in either of the devices (if that can even be concluded from the given information).
Of course, any additional information is welcome, in case I forgot asking something that is deemed important.
Why is this happening?
I tried some time back communicating Arduino-Arduino and Arduino-Pi. I faced some problems with UART communication. However, you might want to keep same Baud rate on both the devices. With Pi, you might need to trigger an event if you receive data from Arduino. On the other side, if you code runs longer, then you might lose some data i.e. your Arduino code is running something else while Pi sends data over UART.
Is this difference in behaviour expected?
Yes. Arduino is a microcontroller based device while Pi is microprocessor based (runs on OS)
Is there a potential problem in either of the devices (if that can even be concluded from the given information).
I don't think there could be any hardware problem unless it is not functioning at all.
Also, because of this issues, I switched from UART communication to SPI communication. This solved my problem completely.
I have an Arduino Uno and I am using arduino 1.0.5 IDE. I followed he procedures for bootloading an atmega328P-PU on a breadboard.
I uploaded the ArduinoISP sketch first, made the connections(using the External Oscillator) and then wired it up. Then, I selected the programmer as Arduino as ISP, selected the board as Arduino duemilanove w/ Atmega328P. Then I selected the correct serial port and clicked Burn Bootloader.
I got the following errors:
avrdude.exe: stk500_program_enable(): protocol error, expect=0x14,
resp=0x50avrdude.exe: initialization failed, rc=-1 Double
check connections and try again, or use -F to override
this check.avrdude.exe: stk500_disable(): protocol error, expect=0x14,
resp=0x51
How to solve this issue? Also, can I upload the bootloader directly by using it on the Uno in place of the original chip. If so, how?
to my understanding the error you have indicates a bad reading from the chip. I experienced that with chips that were either dead or not properly connected, especially to power supply.
You may find more detailed information in th tutorial : https://www.arduino.cc/en/Tutorial/ArduinoISP
Especially those things :
Note for Arduino 1.0: you need to make one small change to the
ArduinoISP code. Find the line in the heartbeat() function that says
"delay(40);" and change it to "delay(20);".
Select the items in the
Tools > Board and Serial Port menus that correspond to the board you
are using as the programmer (not the board being programmed).
Instead of arduino built-in boot loader just go through below link and it will be great for uploading boot loader and verifying board status info
I am replying you this because same issue I got long back and it saved me.
One more thing for arduino boot loader: for atmega328 you need to put capacitor between reset and gnd( in case you missed)
For gammon bootloader you don't need it.
Be Innovative.
For reset line you might me using 100nf(thats what stated in documentation )...but sometimes it doesn't work...try something like 4.7uf, 22uf or 47uf or close values
I had a similar problem and the issue was that my programmer was a bit slow, I used the -B flag for avrdude to slow down the bitrate and it started working, I set the -B20 and works like a charm every time, but I use the USBTinyISP programmer, not the stk500 one, so this might not work for you.
In case someone stuck at this as I did and nothing like changing the cap value helped. Make sure you are using your USB-TTL adapter in a 5v mode (obviously for a 5v powered chip). I always used it in a 3.3v mode in order not to accidentally burn my 3.3v chips and it always worked. Until today, I was trying to flash my custom atmega8 board and everything worked with the ISP but I was having a hard time using the bootloader and after half a day searching and trying different stuff the 5v setting to the rescue.
Please pardon me if this question comes as a little too basic but I have tried searching almost everywhere but haven't found a clue.
I am using the esp8266 module and have uploaded the firmware in it. I have also set it as "Access point" so that other modules are able to connect with it. My problem is that I want to control it pro-grammatically through an 8051 micro-controller. I have searched online and there is a lot of documentation on how it program it through arduino, but that doesn't solve it for me. I want to use assembly language to build a serial protocol that communicates the data from 8051 to esp8266 and then to the connected modules (such as Android device).
My question really is, "would it be possible to just connect TX/RX of 8051 to RX/TX of esp8266 and write a code in assembly that transfers data as I desire to esp8266? Or, do I have to do something else?".
At the moment the only documented way for a host controller (the 8051 in your case) to talk to the ESP8266 is to use the serial port (there is a slave SPI port but the mechanism for driving it isn't known yet). So you will have to make up a little protocol to send and receive commands and data (assuming that the standard support for an enhanced AT command set isn't sufficient for you).
The baud rate can go a lot higher than the default 115200bps, if you need it to (although I'm not sure if the 8051 could keep up).
I recently completed this project with my Arduino (a fairly new hobby for me):
http://www.instructables.com/id/Make-a-24X6-LED-matrix/?ALLSTEPS
I can change the code to make whatever messages I want scroll accross the matrix but I thought it might be cool to have live information, like stock quotes, scroll accross. I think I could figure out how to do that except I would like to use it at work where there are lots of firewalls in place and I doubt Arduino software is on the approved list of programs. Is it possible to send messages to the Arduino through a USB without installing any drivers?
No it is impossible because data in Arduino is sent via serial command, the USB is only for convenience, but arduino work with FTD driver that emulate a serial connection. You should choose another type of connection bluetooth or wifi.
Hope this help you.