I have borrowed an Arduino BT-V06 (analogue) from my college IT storage department.
At home I am trying to do some research on this for subsequent work I am going to perform with this Arduino later on. As this model is a 2006 version; my question is, how do I connect it to my laptop? Some sort of adapter? or perhaps shield it with a newer model that has a usb-port?
Because I would like to have it connected to my laptop in order to try out some codes on it.
Thank you very much for your time!
-M
There's at least two options. First, it's set up to be programmed over Bluetooth. So if you have Bluetooth on your laptop, you can connect the two wirelessly. Pins 0 and 1, per the documentation, are TTL serial transmit and receive pins (which are also used for Bluetooth communications), so if you AREN'T connecting via Bluetooth, you could connect a serial to USB adapter so you can connect to your laptop via USB. This reference has this to also say:
"The on-board serial communication between the bluetooth module and the Arduino sketch (running on the ATmega328) needs to be at 115200 baud (i.e. call Serial.begin(115200) in your setup() function). Communication between the bluetooth module and the computer can be at any baud rate.
Communication between the BT module and the computer can be temperamental. You might want to open the serial monitor a couple of seconds after resetting the board. The text of the Arduino getting started guide is licensed under a Creative Commons Attribution-ShareAlike 3.0 License. Code samples in the guide are released into the public domain."
Related
I have ATMEL ICE C initial connection problems - it cannot read device signature, because of the target board voltage isn't between range of 1.8 to 5.5V. It has measured by the Atmel Studio as 1.3V (when target board is powered by the USB connector) or 0.3V (when USB disconnected from target).
It'a a brand new device, and i never used it before, may be i did something wrong?
I had used before AVR ISP handmade by myself, and had used previously programmed target board for this experiment, to avoid possibility, that board is dead. The target is works and blinking heart beat.
What i has done -
1.Connect the target board to the ICE programmer.
2.power target board by USB.
3.power programmer by USB from PC USB port.
4.open "device programming" tab in AS 7.
5.Make all settings for my chip atmega328p
6.press "apply" then 'read'
7.get err msg that voltage is too low.
(while i had measured it directly, by the digital voltmeter on pins +5V and GND on target
board, it's about 4.5V, same as in ISP connector - measured on 2 and
6 pins.)
=======================================================
#markus-nm where did you take your measurements?
i had measured on pin 2 and 6 of ISP connector and between pin +5V and GND on Arduino Nano board.
What reference was used?
i had used GND pin on target board for the reference.
Did you use the same USB Host for ISP and power?
no, power to target board was from the wall socket USB charger, AND power to Atmel ICE is from personal computer.
If not, did you connect the grounds?
no, but i guess that grounds are already connected on the target board.
Some links to your chip, your board and ISP would be helpful.
ATMEL-ICE-C https://www.microchip.com/en-us/development-tool/ATATMEL-ICE
ARDUINO NANO PRO https://store.arduino.cc/products/arduino-nano
If it's a custom PCB, provide some schematics. Show a wiring diagram of what you did.
no, i had used the standard Nano board (may be not original, but clone, but it is definitely working now, because it can be programmed by the AVRDUDE program and work.)
The Atmel-ICE, by design, has a lot of different ways to hook up the programming connector. Often when I see problems like this it's because the wrong connector is used. Keep in mind the programmer itself has both an AVR and a SAM port. For the Arduino Nano Pro, make sure it's plugged into the AVR port. After that, ensure you're using the correct programming connector on the adapter board that comes with the Atmel-ICE and that it's oriented correctly on the Nano's header.
If that all fails then something is broken.
I am trying to do a sample application using Qt to communicate to Arduino board DUE.
But When one communication is started other is not able to connect,meaning when i start my Arduino first I am not able to start Qt application to read or write data and viceversa.
Can anybody tell me whether this is possible if Yes please help me in this and i ll try to post my sample code.
If I understand your question correctly, you want to be able to connect to your Arduino device (via its USB to RS232 converter) while the Arduino IDE, and thus, the serial monitor is running.
If that's the case, that is simply not possible. Not because of Qt, nor because of Arduino. That's the way serial ports work. You can't connect to the same port twice from different processes.
Since the microcontroller on the Arduino DUE has 4 UARTS, you may consider using one of them (with another USB to serial adapter, and thus, having another COM port showing up on your PC) to interface the board with your Qt application while the Arduino IDE is still connected to the "main" serial port.
Also, keep in mind that the Arduino Due works with 3.3 V, so ensure that the USB to serial adapter is compatbile with that voltage range.
I've got my sim900 module working with arduino by using their software serial library, however, I want to eliminate arduino from the equation and have serial communication directly to sim900 module.
I'm using putty as my terminal emulator. It's serial is configured to COM1 19200 8 N 1 the same as device manager configuration for this port.
I connect straight from hardware serial on my PCs motherboard into serial-to-ttl interface board which connects to sim900 module. The board has 4 pins - VCC GND TX RX. They're all connected to my sim900 hardware serial as follows: VCC=5V GND=GND TX=TX RX=RX (Yes I know that it's always actually TX=RX and RX=TX, but when I connect it that way my interface board doesn't blink any led to indicate a transfer whereas it does when I connect TX=TX and RX=RX). The switch on the module is set to hardware serial pins as well.
So the only thing that happens when I send AT commands such as AT or ATI and press enter is that puttys cursor comes back to the beginning of command that I typed. No response.
I'm thinking that I'm not doing something that the arduinos software serial port is doing when it sends commands to sim900.
Can anyone help please ? It's literally been days of trying different configurations with no results.
In that time besides getting sim900 working with arduino software serial I verified that the hardware serial port on my motherboard is working correctly and the interface board is working correctly as well.
I have the Arduino UNO board and I want to know if it is possible to use both the USB connection (for exchanging data) and the external jack to power supply it.
I will use the following cable: http://ecx.images-amazon.com/images/I/41OMXaj5cPL.SY355.jpg with a AC-DC 5V adaptor in order to power supply the Arduino. However, I want to use also the USB connection in order to send some data from the computer.
Both will be connected at the same time.
In short, I want the Arduino to be able to run even if the computer is OFF and whenever I open the computer to send data to Arduino from USB connection.
Is this possible? Will the Arduino Uno board support it?
Yes. From the official Arduino website:
Power
The Arduino Uno can be powered via the USB connection or with an external power supply. The power source is selected automatically.
External DC power will override USB power if the Arduino detects it. [Source]
as other said, it is absolutely possible to have both usb and power jack plugged in.
but be aware that if you shut down your computer and turn it on after, when reading the usb port you'll restart the Arduino and might loose important data.
yeah both of them can be used. If you want to upload the code in arduino then simply use the usb cable otherwise keep it on adapter. it wont harm the device.
What I personally do is, I keep on plugging the adapter and remove the usb once I am done with uploading and then test it as normally the usb cable is quite small and I normally work on robots so I need long wires.
if you want just plugs it in, it's ok but Arduino board will chose one and usb has priority to other power source.
********* Very important :*****
if you are controlling other circuits, that are connected to an external power supply, with your Arduino and connecting it to your PC's usb, Arduino will have potential difference and it will cause current flow that will damage your PC and Arduino board. if you want to do such thing, you have to shield your Arduino board from your other circuits that you want to control and they have external power source. this could happen with optocouplers for digital ports, non signal analog ports with shield relays, and complex analog circuits for analog signals
I have an Arduino 2560 and would like to send serial data to my PC. However, I am currently not using the Arduino Bootloader because I wanted to use a program that I wrote for an Atmega644 before (as far as I understood, one has to use the Arduino language when using the Bootloader?).
Does anyone know if what I am trying to do is possible with reasonable effort?
Connection to PC via 2560's serial0 does not depend on bootloader (if you plan connection when main program is running). You need 16u2 running to bridge 5V serial UART to USB or you can of course use any other option (e.g. MAX232 or so) to convert 5V UART to USB or RS232. But in case of RS232 double check baud rate error because of 16MHz crystal for particular baudrate.
2560 bootloader just implements firmware flash.