I've been trying to test a FT201XQ USB-I2C breakout board: UMFT201XB-01, so I can connect it to a master device such as an Arduino and sniff what that device is sending through I2C.
To see the output of the slave device I have successfully configured a Virtual COM PORT by installing the D2XX drivers provided by ftdchip.com. I can open the serial port through puTTY and everything seems fine in that regard.
Then, i've loaded the "master_writer" example on my Arduino, which sends 1 byte at a time to an address (0x22 is specified in the UM201XB-01 datasheet as the default address).
Nothing seems to happen in the COM port that i've earlier opened. Do I need to configure/program the FTDI device in some way? In that case, how can I do it, in a general way?
UMFT201XB-01 board http://www.ftdichip.com/Support/Documents/DataSheets/Modules/DS_UMFT201_220_230XB.pdf
Thank you in advance, and sorry if this is a "noob" question : P
Related
I am trying to connect a WiFi module (ESP8266) to a "funduino" development board (Arduino Nano) but I have no success. Since I tried so much schematics I've found on the internet about the connection between them two, I kindly ask here if is anyone who succeed in "pairing" this two devices.
I am asking for the schematic and a functional source code.
Regards
The ESP-01 by default comes with nonOS SDK bootloader that communicated via AT commands, you can find the complete command set from Expressif here. This is designed for an MCU (like Arduino Nano) to use it purely as an WiFi module rather than using it as a stand-alone MCU (for which it will require NodeMCU SDK).
If you ever upload an Arduino sketch up to the ESP-01, it will erase the AT Command firmware.
Assuming your ESP-01 is still having the AT Command firmware. What #Ben provided is a sketch that allows you to type AT commands via the Serial Monitor to internact with the ESP-01, it is manual, and good for testing if ESP-01 is working (you type AT and press return on Serial Monitor, the ESP-01 will ack with Ok) but not practical as a real application. The minimum commands required to established an WiFi connection with ESP-01 is listed below.
AT+CIPMUX=1 - Enable single (0) or multiple connection (1) to the web server.
Multiple connection is a good option if you are repeatedly sending
out or reading data from the Internet.
AT+CWMODE=3 - Set WiFi mode: 1 is station mode (ESP8266 is client), 2 is AP mode
(ESP8266 acts like a WiFi router where your phone or PC can connect),
3 is AP+station mode (make the ESP8266 do both)
AT+CWJAP=“<your-ssid>”,”<your-pw>” - Connect to your WiFi. Provide your SSID name
and password inside the double qoutes.
AT+CIFSR - This returns the IP address of the module, indicating that it has
successfully connected to your WiFi router.
Once the WiFi connection is established, you can further communicate with the ESP-01 via the connection, like accessing a website for example:
AT+CIPSTART=0,"TCP", "www.example.com","80” - Start TCP or UDP connection. The
0 is the id of the connection.
AT+CIPSEND=0,16 - Command to tell the module data is ready to be sent. 0 is the
connection id, and 16 is the length of the data to be sent.
After this command, the ESP8266 will reply with the “>”
character to tell us that it will be waiting for the data to be
sent. If successful, the module will reply with “SEND OK”
GET / HTTP/1.1 - Send the http header, and other data, etc...
You can write your own sketch to automate those AT commands for interacting with with ESP-01 once you understand the AT commands required for establish a WiFi connection.
Here are two resources that I personally found extremely useful for doing more than connecting to WiFi.
STM32-ESP-01 Web Server - although this is for interfacing with STM32, the main difference is the pin assignment, so you should be able to port to Arduino easily.
MQTT via ESP-01
As for hardware interface, please noted that what #Ben provided is correct in principle, but you need to be aware that the ESP-01(ESP8266 to be precise) is a 3V3 MCU, so the connection is depended on what kind of host board you are using. If you are using Arduino Uno/Nano, both are having a 5V MCU, you will need a voltage divider (two resistors to drop the voltage to 3v3 before connecting to ESP-01) or a level shifter chip at least for the ESP-01 Rx pin to avoid the potential damage to the ESP-01.
I bought an ESP12F (esp8266 series). My code a led blinker and works my old ESP12E.
After I uploaded via my COM6 port and started the code on ESP12F then the windows COM6 port disapeared from my device manager :(
The port apeared when I disconnect the USBtoSerial (CH340 based) device from my ESP12F. (The code not relevant able to empty too)
I can't use the ESP12F serial port. :(
What can I do?
Thanks, Gabor
The code not relevant
The COM port works and appear only if the ESP12 GPIO0 connected to GND and after reset.
I found the solution and the main problem. So the esp8266 consume bigger than the USBtoSerial adapter capacity. You need an external 3.3V power source (or battery).
Thanks.
I am able to connect and upload the WifiStatus example per the instructions on the Arduino Site/Examples/Yun. However, when I hit the serial monitor button it is supposed to print out the relevant Wifi stats, instead it says "unable to connect" and the final line goes a bit further..."unable to connect: is the sketch using the bridge". Any ideas? A post suggested reseting the 32U4, which I did, but no luck.
Incidently, all of this is over Wifi. Board and port are set per instructions. Yun pings fine and receives the uploaded sketch fine.
More code is usually more illuminating... so you might get better answers when you provide more information.
"is the sketch using the bridge" seems to indicate that there is some problem with the Bridge library. Is it being initialized? Did initialization (i.e., "Bridge.begin()" succeed?
A sketch with bridge functional and serial monitor via network connection cannot be running simultaneously as they use the same hardware connection.
You may use the serial monitor via USB port, or Serial TX/RX pins, or SoftwareSerial for this.
For a student project we have a device with a serial port (UART) wich communicate with a computer by wire.
As we want to make this system wireless (Device can be far far away from the computer), we had the idea to make the device communicate over IP ;
:
Device Serial port ==> UART/RJ45 converter ? ====> Router ===>Modem
Our question is mainly on the UART RJ45 converter. Does such device exist ? we saw some like this :
http://www.ecnmag.com/product-releases/2008/12/embedded-lan-module-connects-10/100baset-lans
But then how to adress the remote computer ? we would like to copy all traffic from the device and send it back to a specified port on our computer.
We also thought about changing the firmware of the router to OpenWRT to achieve this
Thanks in advance
... You could just get a raspberry Pi, which runs Linux and gives you low level access to a set of IO pins. Or use an Arduino with the Ethernet module. All of which are readily available and easy to procure. The Arduino and Ethernet modules are for sale at just about every Radio Shack these days.
Unless you have a need to communicate at speeds greater than around 100kbps, the above solutions should work fine.
Edit:
Note that there are Serial libraries available for the Pi:
https://projects.drogon.net/raspberry-pi/wiringpi/serial-library/
Finally I found a good solution thanks to you guys.
I ordered an Rasperry Pi which have IO pins as Wing Tang Wong said, including a set of Rx Tx pin functionning at 3,3v.
Our device work at 5v, so we are going to use a logical converter.
On the RPi we are going to use the ser2net package wich translate a serial input to a TCP/IP network signal ;)
Job done !
Thanks again
I'm using an Arduino to read data from the web and display it. I can easily pass the data as serial using the supplied drivers, because they identify the COM port so I can send serial to the COM port.
However, I want to use 'real' USB techniques so the device can be plugged in and out like a normal USB device. I'm looking at using WinUSB as the driver. However, USB is all new to me. Is there an .inf file that uses WinUSB and an Arduino (I have an Uno)?
The lack of information on this is making me think I am going about this incorrectly.
Turns out that an Arduino Uno is not a genuine USB device.
It acts as a Serial to USB adapter. Consequently USB drivers don't talk to it.
I got round this by writing a sketch which reported back what device it was when it got the correct query from the PC.
On the PC I just iterated the Serial ports and sent the query to each port. The one that replied was the Arduino.
After that I record the port number and send serial data to the Arduino.
To learn the USB portion, maybe you could combine V-USB and the UNO?
Check out V-USB.
V-USB is a software-only implementation of a low-speed USB device for Atmel’s AVR® microcontrollers, making it possible to build USB hardware with almost any AVR® microcontroller, not requiring any additional chip.
While not necessarily Arduino, it may provide you the learning exprience you want, and let you use incorporate your UNO device.