everyone!
My problem is when I use the command 'lsusb', The result is:
Bus 002 Device 011: ID 0451:2046 Texas Instruments, Inc. TUSB2046 Hub
Bus 002 Device 012: ID 2047:0013 Texas Instruments
But when I use 'make msp5529 install', it shows:
usbutil: unable to find a device matching 0451:f432
make: * [program] Error 255
I don't know how can I transform '0451:f432' to '0451:2046'. I tried add an rule in /etc/udev/rules.d/82-msp430.rules like '
SUBSYSTEMS=="usb", ATTRS{idVendor}=="0451", ATTRS{idProduct}=="2046", MODE="0666", GROUP="users".'
But it still shows the same error. Do you know why? Thank you very much!! :)
I assume you're playing with the msp430F5529 Launchpad, in which case the 0451:f432 VID/PID won't work. In summary, you'll need to run:
sudo mspdebug tilib "prog bin.elf"
where bin.elf is the binary program that you generated. I found that the easiest way to get a working mspdebug with tilib is downloading the Energia IDE for msp430.
Related
What is the exact FETCH command that is used to read only the text body of message 1?
I tried this below and variations of it but it says BAD Error in IMAP and Unknown command.
**FETCH 1:1 (BODY[HEADER.FIELDS (TEXT)]**
Im executing this in Ubuntu on a terminal for my upcoming exam.
Try _ FETCH 1 (BODY[TEXT]). Why do you have asterisks around your command? You find the possible arguments to the FETCH command in RFC 3501. You can also play around with the interactive tool that I wrote.
I am having some issues getting stock code to compile for my 9 axes motion shield. I have a github repository with all of the motion libraries I have, the example code, and the error messages I am getting.
I am using Arduino 1.7.1 IDE on Windows 7 64-bit.
I have tried using sample code for the sensor instead of for the shield and could not get that to compile either. I have tested example code built into the IDE to ensure that I can compile something and I was even able to interface with my Arduino MEGA 2560 with said code.
I have searched Google and Stack exchange a fair bit and have not managed to come up with any solutions.
The main error I can not figure out is:
"
C:\Users\LJI_eric\Documents\Arduino\sketch_mar20a\sketch_mar20a.ino: In function 'void setup()':
sketch_mar20a:63: error: 'OPERATION_MODE_NDOF' was not declared in this scope
mySensor.setOperationMode(OPERATION_MODE_NDOF);"
OPERATION_MODE_NDOF is a mode that is defined in BNO055.h and is an array of operation modes. I tried several other modes to no avail.
I would appreciate any and all help.
On line 84, 87 and 91 you have made a new line inside a string. You can not do that on the Arduino. If you want to break a string up in more lines you should end the string where you would break it, and start the string again on the new line, like this.
Serial.println("Move the device around and then place it at one position.\n"
"Change the threshold and duration to increase the difficulty level.");
Then you should change OPERATION_MODE_NDOF to BNO055_OPERATION_MODE_NDOF
I use two FIBOCOM G510 GSM modems but one of them returns ERROR in some commands like:
AT+CMGF=1\r, AT+CPIN=? returns ERROR.
But some like ATE0\r, AT+CLIP=1\r, AT+CBAUD?\r returns OK.
I use baudrate 115200.
Q1:ATE0\r
R1:\r\nOK\r\n
Q2:AT+CBAUD?\r
R2:\r\n+CBAUD: 115200\r\n\r\nOK\r\n
Q3:AT+CPIN=?
R3:\r\nERROR\r\n
Q4:AT+CMGF=1
R4:\r\nERROR\r\n
Is there something I should set first or is it simcard issue or modem fault?
My other unit works good but I tested it 3 months ago and I think I would use some additional commands to prepare.
I am confuse what's its wrong?
I checked sim card wiring for 3rd time and I found cardinal mistake. Socket was upside down and even wires was connected to the "right place" it did not comunicate.
After rewiring modem starts to work well.
Q5:AT+CPIN?\r
R5:\r\n+CPIN: READY\r\n\r\nOK\r\n
I'm making a Turbo Pascal 7.0 program for my class, it has to be on Graphic Mode.
A message pops up
BGI Error: Graphics not initialized (use InitGraph).
I'm already using InitGraph and graph.tpu and I specified the route as "C:\TP7\BGI".
My S.O is Windows 7 and I'm using DosBox 0.74, I already tried to paste all the files from the folder BGI into BIN.
What should I do?
Since dos doesn't have system graphic drivers, the BGI functions as such for BP7.
So in short, use a BGI suitable for your videocard. The ones supplied with BP7 are very old, there are newer, VESA ones that you could try.
Afaik 3rd party BGI needs to be registered explicitly in code though.
At first I have had this "missing Graph.tpu"- ... and later the "Use Initgraph"-issue too.
After hours trying (and reading some not politeful comments in the internet) I finally got Turbo Pascal 7 succesfully running (in Windows 10, x64). In summary I want to share "some secrets":
install the "TP(WDB)-7.3.5-Setup.msi" (comes from clever people in Vietnam)
make sure, that there's the CORRECT PATH to the "BGI"-directory in your program-code. For example:
driver := Detect;
InitGraph (driver, modus, 'c:\TPWDB\BGI');
(By the way: This is ALL, what's there to do with "Initgraph".)
make sure, that in TP7 under "Options" --> "Directories" are the CORRECT PATHS both to "C:\TPWDB\UNITS" and Your actual working dir e.g. "C:\TPWDB\myPrograms"
THAT's IT.
Annotations: The "Graph.TPU" (usually) is already in "UNITS" (together with "Graph3.tpu" by the way).
Hazzling around old driver's isn't needed even... :)
Just the correct paths... :)
Hope, that can help ...
I noticed this question has been asked many times in the past and surfing the web I found many pages about it. However, it seems like the proposed solutions rarely work and, in my case, the problem does not refer to a program that I wrote. So I'll give it another try here.
I recently installed Linux Mint 14 on my laptop. After the OS was spick and span, I started to install the software I need, and among these netgen (a Mesh Generator software). I tried both ways: download+unpack+compile+install and synaptic. Either way, this is the output I get when I try to execute the program
X Error of failed request: BadAlloc (insufficient resources for operation)
Major opcode of failed request: 154 (GLX)
Minor opcode of failed request: 3 (X_GLXCreateContext)
Serial number of failed request: 490
Current serial number in output stream: 491
As I said, I surfed the web, and apparently, this is thought to be linked to some problem in the X server configuration. And here start the mess. Someone says I should modify /etc/X11/Xorg.conf, adding the lines
Option "Videoram" "65536"
Option "Cachelines" "1980"
Under the section "Device." Unfortunately, I have no such file, as apparently in recent distros, the X configuration file has been moved to /usr/share/X11/xorg.conf.d/* and it's now split into different files. The one about the monitor and graphics should be called 10-monitor.conf...which I don't have. I tried to create one, following the instruction at this link, and then add those lines, but nothing happened. To be fair, I'm not 100% sure I generated the file correctly since I am not sure how to detect the driver for my graphics card.
I don't know how much and which information people would need to have an idea of how to fix this problem. Here's what I see might be useful.
The output of 'lspci | grep VGA' is
01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee
ATI RS880M [Mobility Radeon HD 4200 Series]
My current /usr/share/X11/xorg.conf.d/10-monitor.conf is the following
Section "Monitor"
Identifier "Monitor0"
Modeline "1920x1080_60.00" 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -HSync +Vsync
EndSection
Section "Device"
Identifier "LVSD"
Driver "fglrx" #Choose the driver used for this monitor
EndSection
Section "Screen"
Identifier "Screen0"
Device "LVDS"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1920x1080_60.00" "1366x768"
EndSubSection
EndSection
Under the section "Device." Unfortunately, I have no such file
Try creating your own xorg.conf file, placing it in this location will override your X settings after restarting X or simply by restarting the computer.
mkdir -p /etc/X11/xorg.conf.d/
cp /etc/X11/xorg.conf.d/xorg.conf /etc/X11/xorg.conf.d/xorg.conf.bk # in case it exists
cp /usr/share/X11/xorg.conf.d/10-monitor.conf /etc/X11/xorg.conf.d/xorg.conf
The content of /etc/X11/xorg.conf.d/xorg.conf would look like (adding your options):
Section "Monitor"
Identifier "Monitor0"
Modeline "1920x1080_60.00" 172.80 1920 2040 2248 2576 1080 1081 1084 1118 -HSync +Vsync
EndSection
Section "Device"
Identifier "LVSD"
Driver "fglrx" #Choose the driver used for this monitor
Option "Videoram" "65536"
Option "Cachelines" "1980"
EndSection
Section "Screen"
Identifier "Screen0"
Device "LVDS"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Depth 24
Modes "1920x1080_60.00" "1366x768"
EndSubSection
EndSection
This also could be related to the driver you're using, there are other common drivers available like
Driver "fbdev"
Driver "vesa"
Driver "fglrx"
The fbdev driver supports all hardware where a framebuffer driver is available.
The vesa driver supports most VESA-compatible video cards. There are some known exceptions, and those should be listed here.
fglrx is a X.org(7x) driver for ATI (Mobility(TM)) RADEON® and (Mobility(TM)) FireGL(TM) based video cards. The driver provides hardware acceleration for 3D graphics and video playback. It includes support for dual displays, TV Output and as of version 8.21.7 also OpenGL 2.0 (GLSL).
Depending on which driver you choose, certain options/functionality/compatibility would be enabled or not, you could change the driver and test with the options you said would work.
Finally, you have hundreds of options here to play with X11.
When I had made written a lot text to my program I took similiar error. When I reduce the text size the error was disappeared. I think you should reduce too showing things or reorganise how they are looking on screen.
I hope I could help you with this broken English ;)