I am using Ableton Live 6 Lite with M-Audio Fast Track connected through USB port. I am having the following issue which I do not know how to resolve: I cannot simultaneously use sound recording with the above mentioned setup and a USB connected keyboard (just a regular USB keyboard which I use with my Toshiba Laptop PC). Either keyboard is not working or no sound reaches Ableton Live software. Any help would be really appreciated. Thanks.
It sounds like you are using a USB hub which does not have its own power source. You are drawing too much current so only one device can be powered at a time. Use USB ports directly on your computer or get a USB hub with its own power adapter.
Related
I have been trying to set the limit of pairing the Bluetooth device HC-05(interface by Arduino controller) with my smartphone.
I have tried making this solution work with AT command
AT+INQM=<Param>,<Param2>,<Param3>
Example: AT+INQM=1,9,48\r\n
But instead of converting AT commands using serial.h with embedded C, I am looking for any dedicated library which helps to work this kind solution in using Arduino.
Basically, with the help of Bluetooth device connect to Arduino Nano, I want to send the altimeter sensor data to my smartphone.
During the connection, HC-05 should be responding any one device at a time, if another smartphone tries to pair then the error will be shown.
Please share your advice on this.
Yes there are some libraries in arduino but these are only meant for connection and pairing and low energy connections. We don't have any dedicated library from where we can control the mode of operation of HC05 or any bluetooth module. like bypassing or accessing GAP and GATT services of bluetooth. However there is a way to flash HC-05. But we can only use it for updating the firmware of this device. This github repo is dedicated for this purpose . Hope it helps you
I have a Microsoft Surface Book that I've dual booted Linux Mint on. I'm writing a program that needs to read in data from a serial port, but my serial ports don't seem to be working. The behavior is consistent across Mint and Windows (Testing done through Cygwin). It gets a bit of data the first 2-5 seconds that the device is plugged in (viewing the data through screen, same thing happens if I just use pyserial to print data incoming from serial port), then nothing.
What could be happening? I think I've isolated the problem to the serial ports - the Surface Book has 2 USB ports and the same thing happens on both of them, and I've tested the hardware that I'm plugging into it on 2 other computers (One Linux and one Mac OS), and it works fine on both of those.
Your MS Surface, seemingly, has a yellow triangle exclamation mark icon (over the adapter icon) without any driver to install/download. And properties in the device status box window say This device cannot start. (Code 10) or A device which does not exist was specified. Right?
If it's so you should wait for an update from MS. It's notorious problem.
I ended up getting the computer replaced on warranty for an unrelated issue months later, and what do you know, on the new computer the serial ports work fine. That indicates to me some sort of hardware problem, given that the issue persisted across OS's.
maybe this will help:
see Arduino examples for serial port communication - search google:
arduino serial c++
arduino serial c#
arduino serial c++ linux
the point is to open port properly you need to open a file, not a port. not with usual c - assembly write to port code.
another option you are using an unintentionally bought fake USB to serial cable with a Fake PL2303 chip
then you need to install the old version of the driver.
search in google:
Fake PL2303 + your os name:
install driver Fake PL2303 windows 10
another option is maybe it conserves energy and closes the port because it feels it is unused.
in windows> device manager,> properties of a device - usually USB root hub > power management - allow the computer to turn off this device to save power - uncheck it.
https://superuser.com/questions/408683/why-my-usb-mouse-gets-suspended-after-3-seconds-of-inactivity
https://blogs.msdn.microsoft.com/usbcoreblog/2013/11/08/help-after-installing-windows-8-1-my-usb-device-doesnt-charge-or-it-disconnects-and-reconnects-frequently/
also, you could look in windows events - to see what happens. usually, failures like this are registered in the events log.
an unlikely option is it consumes too much current, like a short circuit. and the device protection circuit shuts the chip off. also probably it does not have such circuit. one possibility is to try with an external powered hub.
the most probable of these is the power saving mechanism
I was experiencing the same problem - came across the solution on another site. The USB 3 ports on Surface Book aren't compatible with something or other to do with Com Port but running the device through a cheap USB hub solved my problem straight away and it was instantly recognised by the Arduino IDE
We've got two WinCE devices that need to talk to each other, they don't have WiFi or Bluetooth so I think a wired USB connection is our best chance. I've been reading up on using ActiveSync and serial over USB, but all the articles are geared towards talking between a WinCE device to a full Windows box, never between two WinCE devices.
If we can get ActiveSync working, that's fine, the other option is just to open COM ports on both sides and write our own communications protocol.
Given the project timelines, writing any sort of device driver isn't an option, this needs to be something that is built in to WinCE.
We are building WinCE for both devices, so I can make any modifications necessary at that level.
Is there a way to get these two guys talking to each other?
If you can't write your own driver then your fastest route is probably to get a USB to serial converter for both devices and then connect them via serial.
Obviously, you'll need to choose one that has support for Windows Mobile. I think FTDI based adapters should work.
Once that's working you just use the built-in serial API to read and write data.
I'd like to connect a beagleboard-like (custom developed) omap board to a Windows PC using a virtual-com setup. That is, i'd like the board to appear to Windows as a com device and get the COM to send data to our application on the board. The main reason for that is to use virtual-com drivers on windows, since the usb drivers we use now to directly sent data over usb between the host and the board seem not to work properly.
I have done this using the FTDI driver on the past but as far as i know it worked because the device had an FTDI chip that translated the usb protocol to serial signals (am i right ?).If there's no USB to UART bridge on the board, how could i do that ?
By the way, how USB Communication Device Classes fits here ? Should develop a CDC driver for the board ? What should I use then on Windows side ?
I'm kind of confused, so any help will be greatly appreciated :)
Well, i answer myself :)
The solution lies in the Linux USB Gadget Subsystem.
Gadget API
What I have in mind is having a number of sensors (temperature, accelerometer, sound level meter) that are controlled by a micro controller. What I want to do is take this information and transmit it wireless to a laptop that will take this information and put it on to a web server using Zigbee. I don't know where to start.
Since you don't have any hardware as of yet, you might want to give the Arduino a try. The hardware is affordable, can be connected to your system via USB while being programmable in-system.
The basic board can be extended via so called "shields", which offer additional features. In your case, the XBee shield would be appropriate. Connecting your laptop to a XBee module is as simple as using Sparkfun's breakout board and a mini-USB cable.
The Arduino has a large community, so you will find a lot of resources, like books, online material, example code etc.
We also provide wireless modules that can be used for serial data transmission. They can be found at www.starmanelectric.com Our modules are very similar to the xbee, but more plug and play. They can be a great for going wireless for the first time. Our devices are designed to function like a "wireless cable" so if you're used to using wires then you'll be up and running in no time at all. We also have circuit examples for transmitting to a laptop serial port or USB. Any micro-controller will be fine for this application, as long as it has a serial port and a few ADCs to sample your data. Our modules also provide simple analog in/out which can run in parallel to the serial. If you want to compare to other systems, I would google "wireless serial modules"
Regards,
Michael
Starman Electric