I have been trying to set the limit of pairing the Bluetooth device HC-05(interface by Arduino controller) with my smartphone.
I have tried making this solution work with AT command
AT+INQM=<Param>,<Param2>,<Param3>
Example: AT+INQM=1,9,48\r\n
But instead of converting AT commands using serial.h with embedded C, I am looking for any dedicated library which helps to work this kind solution in using Arduino.
Basically, with the help of Bluetooth device connect to Arduino Nano, I want to send the altimeter sensor data to my smartphone.
During the connection, HC-05 should be responding any one device at a time, if another smartphone tries to pair then the error will be shown.
Please share your advice on this.
Yes there are some libraries in arduino but these are only meant for connection and pairing and low energy connections. We don't have any dedicated library from where we can control the mode of operation of HC05 or any bluetooth module. like bypassing or accessing GAP and GATT services of bluetooth. However there is a way to flash HC-05. But we can only use it for updating the firmware of this device. This github repo is dedicated for this purpose . Hope it helps you
Related
I'am working on an IOT project. The goal is to communicate between two openmotes (one is the server and one is the client). When the client receives some data, it is supposed to pass it to an arduino to activate different controllers (like a motor, some leds ...). So, I wanna send data from a openmote to an arduino. The idea is to use a bus. The openmote is the master and the arduino is the slave. Do you have any idea how to do this ? I can't find any documentation fro the open mote part. I thought about using the serial UART but i don't have any idea how to do that.
Thank you !
If anyone is looking for an answer, it is possible to activate the UART 1 on the open mote and to send data to the arduino using that bus. You have to pay attention to the speed you are using on both sides.You can refer to this file to see the functions to use: https://github.com/contiki-os/contiki/blob/master/examples/cc2538-common/test-uart.c
Firstly, I'll just give you a brief introduction about our project... its "Speech controlled Home Automation System" where we are controlling the Home appliances by the voice or speech commands. We're successfully done with the voice recognition module. But our problem is with achieving the communication between the transmitter {where the user gives the voice command} and receiver {where the home appliances are present} through WiFi i.e. we have got 2 ESP8266 12E modules interfaced with Arduino both at the transmitter and receiver side and these two WiFi modules need to be communicated(To interchange some data sent by Arduinos).So please let us know which Arduino code need to be used at transmitter side wifi module and at Receiver side wifi module and also about the header files or additional softwares(if any)to be used.
you can achieve this by starting one of wifi modules in Access Point Mode and the other one has to be set to Station Mode in order to connect to the first one.
In case you want to add a router, just set both ESP8266 modules to Station Mode and connect them to the router.
And then transfer any data you want through AT commands of ESP8266.
Here is the refrence to them.
https://room-15.github.io/blog/2015/03/26/esp8266-at-command-reference/
If you are newbie to Esp8266 and Arduino , this will help you.
http://www.teomaragakis.com/hardware/electronics/how-to-connect-an-esp8266-to-an-arduino-uno/
Good Luck !
I worked on a similar system a year ago. I was developing a remote controlled toy. My main difference was I used the ESP8266 without an Arduino attached.
One ESP worked as a a WiFi hotspot and the other connected to it, sending messages through UDP.
For some reason, I could not get the two ESP modules to connect (I think it was a problem with the board I had), but I sent messages from my computer, and it worked out fine. I will not burden you with all of the code, but here is the GitHub link.
All that needs to happen is they will be on the same WiFi network, and then you can use the ESP8266 WiFi library to send messages between the two. Like I said above, I used UDP, which is good for high speed, with no error checking. But there is also TCP (higher up, has error checking code), or you can use the server/client part of the library to set up a full web server and read/write data to it. Without knowing what type of data, I cannot comment on what would be the best method.
As for headers, you will need WiFi.h, and if you are using UDP you will need WiFiUdp.h
You should not need any external software besides the Arduino IDE.
I taught myself from scratch for this product, using two main resources: the Arduino library reference, and the docs on the ESP8266 Arduino GitHub page
I am new to Arduino and I would like to do a project that sends data, remotely. So, the Arduino would not be connected to Wifi/Bluetooth, Ethernet, etc. Would using a GSM shield be the best way to transfer data? I do not need to make phone calls or send SMS (unless sending SMS would be a better, more reliable, option) just data to a server, who's app I would create. If this is the best option, what else would I need to make this happen? For example, on top of the GSM shield (I am looking at something cheap like this: https://www.amazon.com/Geeetech-SIMCOM-Quad-band-Development-Arduino/dp/B00A8DDYB6/ref=sr_1_2?ie=UTF8&qid=1467651878&sr=8-2&keywords=Arduino+GSM+Shield) what other charges would I need to pay? I.E. would I also need to get another phone plan? Would I have to pay for a gateway service that would receive the cell phone data and then send it to my server?
Thanks your any thoughts on this
Wifi, ethernet or GSM, it depends on what you want to use, and what you have.
With all three you can send data to a server.
There is a bench of Arduino shields. All shields from Arduino come with a library to handle communication.
Other shields from other vendors exist and they provide their libraries too.
For Ethernet you can check the arduino shield https://www.arduino.cc/en/Main/ArduinoBoardEthernet.
For Wifi there are plenty. You have first the arduino shield. You can also take a look at the CC3000. Or the famous ESP8266. For all three you can find libraries.
For GSM, Arduino has a shield and a library. Arduino uses the Quectel M10 GSM moduel. You can find lots of examples in the arduino website and all over the net (https://www.arduino.cc/en/Guide/ArduinoGSMShield).
There exist other shields like the one you mentioned. Libraries does exist for those "other" shields however they are not as maintained as the arduino one.
You need to be careful though, you'll find over Amazon (and most likely on Alibaba) some GSM modules like SIM900A that are way cheaper, those are only dual band and will work only on certain contries.
There is another cheap GSM Module called the A6. It was made by espressif the company behid the ESP8266. It's relatively new and no library exist for it at the time. You can write you own functions to use it, but that would be some extra work.
In all cases, to use a GSM module you'll need a sim card with it's phone plan and all.
Another thing to consider is how to power these shields. They use more power than an Arduino can generate (A GSM modules datasheet recommend to use a power supply that can deliver up to 2A). If you power them straight from the Arduino, you may encounter some strange behaviour.
So the ideal way is to have for them an external power supply with the required amps and have a commun ground with the Arduino.
I have some sensors connected to my ardunio uno and get periodically data from that sensors now I wanted to send that data to cloud.
I dont have any idea about how should I connect my arduino to Internet using GSM. How should I solve this problem or any alternative is there.
Just get an appropriate shield (like this one) and follow the documents included with it. The linked shield includes some basic service plan as part of the purchase. Once connected, it's just like using any other TCP/IP application.
I recently completed this project with my Arduino (a fairly new hobby for me):
http://www.instructables.com/id/Make-a-24X6-LED-matrix/?ALLSTEPS
I can change the code to make whatever messages I want scroll accross the matrix but I thought it might be cool to have live information, like stock quotes, scroll accross. I think I could figure out how to do that except I would like to use it at work where there are lots of firewalls in place and I doubt Arduino software is on the approved list of programs. Is it possible to send messages to the Arduino through a USB without installing any drivers?
No it is impossible because data in Arduino is sent via serial command, the USB is only for convenience, but arduino work with FTD driver that emulate a serial connection. You should choose another type of connection bluetooth or wifi.
Hope this help you.