Arduino issues with fsr and LCD - arduino

Question

I am doing a project which requires the use of arduino uno, 4 force sensors and a 16x2 LCD. I'm trying to display the readings of the force sensors onto the LCD with the implementation of the buttons. For eg. if I press the up button it should display the first force sensor reading. The problem is it just displays a huge number of 143164976.0000 even when no force is applied on it. Please advice on whether there is a problem to my coding.
int iForceSensorReading; // the analog reading from the FSR resistor divider
int iForceSensorReading1;
int iForceSensorReading2;
int iForceSensorReading3;
int iForceSensorVoltage; // the analog reading converted to voltage
int iForceSensorVoltage1;
int iForceSensorVoltage2;
int iForceSensorVoltage3;
unsigned long ulForceSensorResistance;// The voltage converted to resistance, can be very big so make "long"
unsigned long ulForceSensorResistance1;
unsigned long ulForceSensorResistance2;
unsigned long ulForceSensorResistance3;
unsigned long ulForceSensorConductance;
unsigned long ulForceSensorConductance1;
unsigned long ulForceSensorConductance2;
unsigned long ulForceSensorConductance3;
float FsrForce = 0; // Finally, the resistance converted to force
float FsrForce1 = 0;
float FsrForce2 = 0;
float FsrForce3 = 0;
#include <Wire.h>
#include <Adafruit_MCP23017.h>
#include <Adafruit_RGBLCDShield.h>
Adafruit_RGBLCDShield lcd = Adafruit_RGBLCDShield();
#define RED 0x1
#define YELLOW 0x3
#define GREEN 0x2
#define TEAL 0x6
#define BLUE 0x4
#define VIOLET 0x5
#define WHITE 0x7
void setup(void){
Serial.begin(9600); // send debugging information via the Serial monitor
lcd.begin(16, 2);
lcd.print("Hand Muscle");
lcd.setCursor(0,1);
lcd.print("Meter");
lcd.setBacklight(WHITE);
}
uint8_t i=0;
void loop(void){
uint8_t buttons = lcd.readButtons();
iForceSensorReading = analogRead(A0);//read index finger pressure
delay(30);
// analog voltage reading ranges from about 0 to 1023 which maps to 0V to 5V (= 5000mV)
iForceSensorVoltage = map(iForceSensorReading, 0, 1023, 0, 5000);
ulForceSensorConductance = conductanceFunction(ulForceSensorResistance, iForceSensorVoltage);
if (ulForceSensorConductance <= 1000){
FsrForce = ulForceSensorConductance / 80;
}
else{
FsrForce = ulForceSensorConductance - 1000;
FsrForce /= 30;
}
iForceSensorReading1 = analogRead(A1);//read middle finger pressure
delay(30);
iForceSensorVoltage1 = map(iForceSensorReading1, 0, 1023, 0, 5000);
if (iForceSensorVoltage1 == 0){
}
else{
ulForceSensorConductance1 = conductanceFunction(ulForceSensorResistance1, iForceSensorVoltage1);
delay(30);
}
if (ulForceSensorConductance1 <= 1000){
FsrForce1 = ulForceSensorConductance1 / 80;
}
else{
FsrForce1 = ulForceSensorConductance1 - 1000;
FsrForce1 /= 30;
}
iForceSensorReading2 = analogRead(A2);// read ring finger pressure
delay(30);
iForceSensorVoltage2 = map(iForceSensorReading2, 0, 1023, 0, 5000);
ulForceSensorConductance2 = conductanceFunction(ulForceSensorResistance2, iForceSensorVoltage2);
if (ulForceSensorConductance2 <= 1000){
FsrForce2 = ulForceSensorConductance2 / 80;
}
else{
FsrForce2 = ulForceSensorConductance2 - 1000;
FsrForce2 /= 30;
}
iForceSensorReading3 = analogRead(A3);//read little finger pressure
delay(30);
iForceSensorVoltage3 = map(iForceSensorReading3, 0, 1023, 0, 5000);
ulForceSensorConductance3 = conductanceFunction(ulForceSensorResistance3, iForceSensorVoltage3);
if (ulForceSensorConductance3 <= 1000)
{FsrForce3 = ulForceSensorConductance3 / 80;
}else
{FsrForce3 = ulForceSensorConductance3 - 1000;
FsrForce3 /= 30;
}
if (buttons) {
lcd.clear();
lcd.setCursor(0,0);
if (buttons & BUTTON_UP) {
lcd.print("Index Finger: ");
lcd.setCursor(0,1);
lcd.print(FsrForce,DEC);
lcd.setBacklight(WHITE);
}
if (buttons & BUTTON_DOWN) {
lcd.print("Little Finger: ");
lcd.setCursor(0,1);
lcd.print(FsrForce3,DEC);
lcd.setBacklight(WHITE);
}
if (buttons & BUTTON_LEFT) {
lcd.print("Middle Finger: ");
lcd.setCursor(0,1);
lcd.print(FsrForce1,DEC);
lcd.setBacklight(WHITE);
}
if (buttons & BUTTON_RIGHT) {
lcd.print("Ring Finger: ");
lcd.setCursor(0,1);
lcd.print(FsrForce2,DEC);
lcd.setBacklight(WHITE);
}
if (buttons & BUTTON_SELECT) {
lcd.print("SELECT ");
lcd.setBacklight(WHITE);
}
}
}
// The voltage = Vcc * R / (R + FSR) where R = 10K and Vcc = 5V
// so FSR = ((Vcc - V) * R) / V
int conductanceFunction(long x, long y)
{long result;
x = 5000 - y; // fsrVoltage is in millivolts so 5V = 5000mV
x *= 10000; // 10K resistor
x /= y;
result = 1000000/x; //ulForceSensorConductance2 = 1000000 measured in micromhos
return result;
}

Answer 1

first likely issue, is this symptom sounds like a signed vs un-signed conflict. I see in your code the following calls
ulForceSensorConductance = conductanceFunction(ulForceSensorResistance, iForceSensorVoltage);
where
int conductanceFunction(long x, long y)
but
int iForceSensorVoltage;
You are passing an int(signed) into the second argument. Using it on math and creating a resultant variable of
long result;
and returning that as a INT.
Where you may have other problems.
You should follow some basic diagnostic procedures.
Assuming this problem is on ALL channels. if not then it is likely electrical.
Focusing on one channel.
PUT IN PRINTS of the various variables, to see what is moving as expected and validate the math is as expected